| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2463 bảng dữ liệu(PDF) 701 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2463 bảng dữ liệu(HTML) 701 Page - Renesas Technology Corp |
|
701 / 1250 page ![]() Section 18 I 2C Bus Interface (IIC) Rev. 2.00 Aug. 20, 2008 Page 653 of 1198 REJ09B0403-0200 18.6 Usage Notes 1. In master mode, if an instruction to generate a start condition is immediately followed by an instruction to generate a stop condition, neither condition will be output correctly. To output consecutive start and stop conditions*, after issuing the instruction that generates the start condition, read the relevant DR registers of I 2C bus output pins, check that SCL and SDA are both low. If the ICE bit is set to 1, pin state can be monitored by reading DR register. Then issue the instruction that generates the stop condition. Note that SCL may not yet have gone low when BBSY is cleared to 0. Note: * An illegal procedure in the I 2C bus specification. 2. Either of the following two conditions will start the next transfer. Pay attention to these conditions when accessing to ICDR. Write to ICDR when ICE = 1 and TRS = 1 (including automatic transfer from ICDRT to ICDRS) Read from ICDR when ICE = 1 and TRS = 0 (including automatic transfer from ICDRS to ICDRR) 3. Table 18.11 shows the timing of SCL and SDA outputs in synchronization with the internal clock. Timings on the bus are determined by the rise and fall times of signals affected by the bus load capacitance, series resistance, and parallel resistance. Table 18.11 I 2C Bus Timing (SCL and SDA Outputs) Item Symbol Output Timing Unit Notes SCL output cycle time t SCLO 28 t cyc to 512 tcyc ns SCL output high pulse width t SCLHO 0.5 t SCLO ns SCL output low pulse width t SCLLO 0.5 t SCLO ns SDA output bus free time t BUFO 0.5 t SCLO – 1 tcyc ns Start condition output hold time t STAHO 0.5 t SCLO – 1 tcyc ns Retransmission start condition output setup time t STASO 1 t SCLO ns Stop condition output setup time t STOSO 0.5 t SCLO + 2 tcyc ns Data output setup time (master) 1 t SCLLO – 3 tcyc Data output setup time (slave) t SDASO 1 t SCLLO – (6 tcyc or 12 tcyc*) ns Data output hold time t SDAHO 3 t cyc ns See figure 31.32 (reference) Note: * 6 t cyc when IICXn is 0, 12 tcyc when IICXn is 1 (n = 0 to 5). |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |