| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2117R bảng dữ liệu(PDF) 132 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2117R bảng dữ liệu(HTML) 132 Page - Renesas Technology Corp |
|
132 / 1024 page ![]() Section 5 Interrupt Controller Rev. 1.00 Apr. 28, 2008 Page 106 of 994 REJ09B0452-0100 When the interrupts are requested while IRQ15 to IRQ0 interrupt requests are generated at low level of IRQn input, hold the corresponding IRQ input at low level until the interrupt handling starts. Then put the relevant IRQ input back to high level within the interrupt handling routine and clear the IRQnF bit (n = 15 to 0) in ISR to 0. If the relevant IRQ input is put back to high level before the interrupt handling starts, the relevant interrupt may not be executed. The detection of IRQ15 to IRQ0 interrupts does not depend on whether the relevant pin has been set for input or output. Therefore, when a pin is used as an external interrupt input pin, clear the DDR bit of the corresponding port to 0 so it is not used as an I/O pin for another function. A block diagram of interrupts IRQ15 to IRQ0 is shown in figure 5.4. IRQnE IRQnF S R Q IRQn ISSm ExIRQn IRQn interrupt request Clear signal IRQnSCA, IRQnSCB n = 15 to 7 m = 15 to 7 Note: Switching between the IRQ6 and ExIRQ6 pins is controlled by the EIVS bit. Edge/level detection circuit Figure 5.4 Block Diagram of Interrupts IRQ15 to IRQ0 (3) KIN15 to KIN0 Interrupts Interrupts KIN15 to KIN0 are requested by the input signals on pins KIN15 to KIN0. Functions of interrupts KIN15 to KIN0 change as follows according to the setting of the EIVS bit in system control register 3 (SYSCR3). • H8S/2140B Group compatible vector mode (EIVS = 0 in SYSCR3) Interrupts KIN15 to KIN8 correspond to interrupt IRQ7, and interrupts KIN7 to KIN0 correspond to interrupt IRQ6. The pin conditions for generating an interrupt request, whether the interrupt request is enabled, interrupt control level setting, and status of the interrupt request for the above interrupts are in accordance with the settings and status of the relevant interrupts IRQ7 and IRQ6. KIN15 to KIN0 interrupt requests can be masked by using KMIMRA and KMIMR. If the KIN7 to KIN0 pins are specified to be used as key-sensing interrupt input pins, the interrupt sensing condition for the corresponding interrupt source (IRQ6 or IRQ7) must be set to low-level sensing or falling-edge sensing. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |