| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M32C80 bảng dữ liệu(PDF) 49 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
M32C80 bảng dữ liệu(HTML) 49 Page - Renesas Technology Corp |
|
49 / 352 page ![]() Page 30 0 3 3 f o 5 0 0 2 , 1 0 . v o N 0 0 . 1 . v e R 0 0 1 0 - 1 7 2 0 B 9 0 J E R 5. Reset p u o r G 0 8 / C 2 3 M 5. Reset Hardware reset 1, software reset, and watchdog timer reset are available to reset the microcomputer. 5.1 Hardware Reset 1 ____________ Pins, the CPU and SFRs are reset by setting the RESET pin. If the supply voltage meets the recommended ___________ operating conditions, all pins are reset when a low-level ("L") signal is applied to the RESET pin (see Table 5.1). The oscillation circuit is also reset and the main clock starts oscillating. The CPU and SFR are reset ____________ when the signal applied to the RESET pin changes "L" to high level ("H"). The microcomputer executes the program in an address indicated by the reset vector. The internal RAM is not reset. When an "L" signal is ____________ applied to the RESET pin while writing data to the internal RAM, the internal RAM is in an indeterminate state. Figure 5.1 shows an example of the reset circuit. Figure 5.2 shows a reset sequence. Table 5.1 lists pin ____________ states while the RESET pin is held "L". 5.1.1 Reset on a Stable Supply Voltage ____________ (1) Apply an "L" signal to the RESET pin (2) Provide 20 or more clock cycle inputs into the XIN pin ____________ (3) Apply an "H" signal to the RESET pin 5.1.2 Power-on Reset ____________ (1) Apply an "L" signal to the RESET pin (2) Raise the supply voltage to the recommended operating level (3) Insert td(P-R) ms as wait time for the internal voltage to stabilize (4) Provide 20 or more clock cycle inputs into the XIN pin ____________ (5) Apply an "H" signal to the RESET pin Figure 5.1 Reset Circuit RESET VCC1 RESET VCC1 0V 0V Recommended operating voltage 0.2VCC1 or below 0.2VCC1 or below NOTE: 1. If VCC1>VCC2, the VCC2 voltage must be lower than that of VCC1 when the power is being turned on or off. td(P-R) + 20 or more clock cycle inputs provided into the XIN pin |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |