3822 datasheet(49/59 Pages) RENESAS

49 / 59 page

Rev.1.20

Dec 24, 2003

page 49 of 57

3822 Group (A ver.)

P00–P07, P10–P17, P20–P27 (Note 1)

P41–P47, P50–P57, P60–P67, P70, P71 (Note 1)

P00–P07, P10–P17, P20–P27 (Note 1)

P41–P47, P50–P57, P60–P67, P70, P71 (Note 1)

P00–P07, P10–P17, P20–P27 (Note 1)

P41–P47, P50–P57, P60–P67, P70, P71 (Note 1)

P00–P07, P10–P17, P20–P27 (Note 1)

P41–P47, P50–P57, P60–P67, P70, P71 (Note 1)

P00–P07, P10–P17 (Note 2)

P20–P27, P41–P47, P50–P57, P60–P67, P70, P71

(Note 2)

P00–P07, P10–P17 (Note 2)

P20–P27, P41–P47, P50–P57, P60–P67, P70, P71

(Note 2)

P00–P07, P10–P17 (Note 3)

P20–P27, P41–P47, P50–P57, P60–P67, P70, P71

(Note 3)

P00–P07, P10–P17 (Note 3)

P20–P27, P41–P47, P50–P57, P60–P67, P70, P71

(Note 3)

–40

–20

–2

–5

(VCC = 1.8 to 5.5 V, Ta = –20 to 85 °C, unless otherwise noted)

Notes 1: The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value

measured over 100 ms. The total peak current is the peak value of all the currents.

2: The peak output current is the peak current flowing in each port.

3: The average output current is an average value measured over 100 ms.

4: When the A-D converter is used, refer to the recommended operating condition for A-D converter.

5: When using the microcomputer in low-speed mode, make sure that the sub-clock input oscillation frequency on condition that f(XCIN) < f(XIN)/3.

6: Oscillation start voltage and oscillation start time depend on the oscillator, the circuit constant and temperature. Especially high-frequency oscillator

will require some conditions of oscillation.

“H” total peak output current

“L” total peak output current

“H” total average output current

“L” total average output current

“H” peak output current

ΣIOH(peak)

ΣIOL(peak)

ΣIOH(avg)

ΣIOL(avg)

IOH(peak)

Symbol

Parameter

Limits

Min.

Unit

Typ.

Max.

IOL(peak)

IOH(avg)

IOL(avg)

–1.0

–2.5

“L” peak output current

“H” average output current

“L” average output current

Input frequency for timers X and Y

(duty cycle 50%)

IOL(avg)

f(CNTR0)

f(CNTR1)

MHz

kHz

(4.5 V

≤ VCC ≤ 5.5 V)

(4.0 V

≤ VCC ≤ 4.5 V)

(2.0 V

≤ VCC ≤ 4.0 V)

(VCC

≤ 2.0 V)

High-speed mode

(4.5 V

≤ VCC ≤ 5.5 V)

High-speed mode

(4.0 V

≤ VCC ≤ 4.5 V)

High-speed mode

(2.0 V

≤ VCC ≤ 4.0 V)

Middle-speed mode (Note 6)

(3.0 V

≤ VCC ≤ 5.5 V)

Middle-speed mode (Note 6)

(2.0 V

≤ VCC ≤ 5.5 V)

Middle-speed mode (Note 6)

32.768

Main clock input oscillation frequency

(duty cycle 50%)

(Note 4)

Sub-clock input oscillation frequency

(duty cycle 50%)

(Notes 5, 6)

f(XIN)

2.5

5.0

2 ✕ VCC – 4

VCC

5 ✕ VCC – 8

10.0

4 ✕ VCC – 8

2 ✕ VCC

10.0

8.0

6.0

Table 14 Recommended operating conditions (A version)

f(XCIN)

3822 bảng dữ liệu(PDF) 49 Page - Renesas Technology Corp

3822 bảng dữ liệu(HTML) 49 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

bảng dữ liệu tải về

Link URL