ST72334J2TASLASHXXX datasheet(83/150 Pages) STMICROELECTRONICS

83 / 150 page

ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto

83/150

SERIAL PERIPHERAL INTERFACE (Cont’d)

13.4.7 Register Description

CONTROL REGISTER (CR)

Read/Write

Reset Value: 0000xxxx (0xh)

Bit 7 = SPIE Serial peripheral interrupt enable.

This bit is set and cleared by software.

0: Interrupt is inhibited

1: An SPI interrupt is generated whenever SPIF=1

or MODF=1 in the SR register

Bit 6 = SPE Serial peripheral output enable.

This bit is set and cleared by software. It is also

cleared by hardware when, in master mode, SS=0

(see Section 13.4.4.5 "Master Mode Fault" on

page 80).

0: I/O port connected to pins

1: SPI alternate functions connected to pins

The SPE bit is cleared by reset, so the SPI periph-

eral is not initially connected to the external pins.

Bit 5 = SPR2 Divider Enable.

this bit is set and cleared by software and it is

cleared by reset. It is used with the SPR[1:0] bits to

set the baud rate. Refer to Table 17.

0: Divider by 2 enabled

1: Divider by 2 disabled

Bit 4 = MSTR Master.

This bit is set and cleared by software. It is also

cleared by hardware when, in master mode, SS=0

(see Section 13.4.4.5 "Master Mode Fault" on

page 80).

0: Slave mode is selected

1: Master mode is selected, the function of the

SCK pin changes from an input to an output and

the functions of the MISO and MOSI pins are re-

versed.

Bit 3 = CPOL Clock polarity.

This bit is set and cleared by software. This bit de-

termines the steady state of the serial Clock. The

CPOL bit affects both the master and slave

modes.

0: The steady state is a low value at the SCK pin.

1: The steady state is a high value at the SCK pin.

Bit 2 = CPHA Clock phase.

This bit is set and cleared by software.

0: The first clock transition is the first data capture

edge.

1: The second clock transition is the first capture

edge.

Bit 1:0 = SPR[1:0] Serial peripheral rate.

These bits are set and cleared by software.Used

with the SPR2 bit, they select one of six baud rates

to be used as the serial clock when the device is a

master.

These 2 bits have no effect in slave mode.

Table 17. Serial Peripheral Baud Rate

SPIE SPE SPR2 MSTR CPOL CPHA SPR1 SPR0

Serial Clock

SPR2

SPR1

SPR0

fCPU/4

fCPU/8

fCPU/16

fCPU/32

fCPU/64

fCPU/128

ST72334J2TA/XXX bảng dữ liệu(PDF) 83 Page - STMicroelectronics

ST72334J2TA/XXX bảng dữ liệu(HTML) 83 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL