công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

RHFL7913SCA1 bảng dữ liệu(PDF) 10 Page - STMicroelectronics

tên linh kiện RHFL7913SCA1
Giải thích chi tiết về linh kiện  Rad-hard adjustable negative voltage regulator
PDF  19 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  STMICROELECTRONICS [STMicroelectronics]
Trang chủ  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

RHFL7913SCA1 bảng dữ liệu(HTML) 10 Page - STMicroelectronics

Back Button RHFL7913SCA1 Datasheet HTML 6Page - STMicroelectronics RHFL7913SCA1 Datasheet HTML 7Page - STMicroelectronics RHFL7913SCA1 Datasheet HTML 8Page - STMicroelectronics RHFL7913SCA1 Datasheet HTML 9Page - STMicroelectronics RHFL7913SCA1 Datasheet HTML 10Page - STMicroelectronics RHFL7913SCA1 Datasheet HTML 11Page - STMicroelectronics RHFL7913SCA1 Datasheet HTML 12Page - STMicroelectronics RHFL7913SCA1 Datasheet HTML 13Page - STMicroelectronics RHFL7913SCA1 Datasheet HTML 14Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 19 page
background image
Application information
RHFL7913A
10/19
6
Application information
Adjusting output voltage: R1 resistor must be connected between VO and ADJ pins. R2
resistor must be connected between ADJ and GND pins. Resistor values can be derived
from the following formula:
VO = VADJ (1 + R1/R2) with VADJ = -1.20 V
To access all RHFL7913A adjustable functionality, V (+) shall be set at 3.0 V (max 5 V). As a
consequence, VI (-) cannot be greater than –9.0 V (resp. –7 V) due to –12 V maximum
operation rating.
The device is functional as soon as VI - VO voltage difference is slightly above power
element saturation voltage. The adjustable pin to Ground resistor shall not be greater than
10 k
Ω to make output feedback error be below 0.2%. A minimum 0.5 mA IO is necessary to
set to ensure perfect “no-load” regulation. It can be wise to dissipate this current into the
divider bridge resistor.
All available VI pins shall always be PCB interconnected, the same for all available VO pins,
otherwise device stability and reliability cannot be granted. The INHIBIT function switches
off output current in an electronic way, is very quickly. According to Lenz’ Law, external
circuitry reacts with –LdI/dt terms which can be of high amplitude in case some series-
inductance exists. Effect would be large transient voltage developed on both device
terminals. External Schottky diodes set on VI and VO may prevent voltage excursions
beyond max ratings. In the worst case, a 14 V Zener diode shall protect the device input. In
case of capacitive load, a input-output protection diode can be necessary to prevent VO to
be greater than VI during transient operation.
The device has been designed for high stability and low drop out operation: minimum 1 µF
input and output tantalum capacitors are therefore mandatory. Typical industry PCB design
practices 10 µF capacitors values are acceptable. Capacitor ESR range is from 0.020
Ω to
over 20
Ω. Such range turns out to be useful when ESR increases at low temperature. When
large transient currents are expected, larger value capacitors are necessary.
In case of high current operation with expected short-circuit events, caution shall be
considered relatively to capacitors. They shall be connected as close as possible form
device terminals. As some tantalum capacitors may permanently fail when submitted to high
charge-up surge currents, it is recommended to decouple them with 470 nF polyester or
ceramic capacitors.
RHFL7913A adjustable being manufactured with very high speed bipolar technology (6 GHz
fT transistors), the PCB layout shall be performed with unprecedented care, very low
inductance, low mutually coupling lines, otherwise high frequency parasitic signals may be
picked-up by the Device resulting into system self-oscillation. In difficult high current
circumstances (coming from PCB layout) a 470 nF polyester capacitor connected between
VO and ADJ pin increases stability margins. Benefit is SVR performances extended to far
higher frequencies.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com