ST723216 datasheet(55/185 Pages) STMICROELECTRONICS

55 / 185 page

ST72321

55/185

WATCHDOG TIMER (Cont’d)

10.1.5 Low Power Modes

10.1.6 Hardware Watchdog Option

If Hardware Watchdog is selected by option byte,

the watchdog is always active and the WDGA bit in

the WDGCR is not used. Refer to the Option Byte

description.

10.1.7

Using

Halt

Mode

with

the

WDG

(WDGHALT option)

The following recommendation applies if Halt

mode is used when the watchdog is enabled.

– Before executing the HALT instruction, refresh

the WDG counter, to avoid an unexpected WDG

reset immediately after waking up the microcon-

troller.

10.1.8 Interrupts

None.

10.1.9 Register Description

CONTROL REGISTER (WDGCR)

Read /Write

Reset Value: 0111 1111 (7F h)

Bit 7 = WDGA

Activation bit.

This bit is set by software and only cleared by

hardware after a reset. When WDGA = 1, the

watchdog can generate a reset.

0: Watchdog disabled

1: Watchdog enabled

Note: This bit is not used if the hardware watch-

dog option is enabled by option byte.

Bit 6:0 = T[6:0]

7-bit counter (MSB to LSB).

These bits contain the value of the watchdog

counter. It is decremented every 16384 fOSC2 cy-

cles (approx.). A reset is produced when it rolls

over from 40h to 3Fh (T6 becomes cleared).

Mode

Description

SLOW

No effect on Watchdog.

WAIT

No effect on Watchdog.

HALT

OIE bit in

MCCSR

WDGHALT bit

in Option

Byte

No Watchdog reset is generated. The MCU enters Halt mode. The Watch-

dog counter is decremented once and then stops counting and is no longer

able to generate a watchdog reset until the MCU receives an external inter-

rupt or a reset.

If an external interrupt is received, the Watchdog restarts counting after 256

or 4096 CPU clocks. If a reset is generated, the Watchdog is disabled (reset

state) unless Hardware Watchdog is selected by option byte. For applica-

tion recommendations see Section 10.1.7 below.

A reset is generated.

No reset is generated. The MCU enters Active Halt mode. The Watchdog

counter is not decremented. It stop counting. When the MCU receives an

oscillator interrupt or external interrupt, the Watchdog restarts counting im-

mediately. When the MCU receives a reset the Watchdog restarts counting

after 256 or 4096 CPU clocks.

WDGA

ST723216 bảng dữ liệu(PDF) 55 Page - STMicroelectronics

ST723216 bảng dữ liệu(HTML) 55 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL