| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
EX-Z11FB-P-R bảng dữ liệu(PDF) 5 Page - Panasonic Semiconductor |
|
|
|||||||||||||||||||||||||||||
EX-Z11FB-P-R bảng dữ liệu(HTML) 5 Page - Panasonic Semiconductor |
|
5 / 8 page ![]() SPECIFICATIONS Type Thru-beam Front sensing Side sensing Front sensing Side sensing Front sensing Side sensing Model No. (Note 2) Light-ON EX-Z11FA(-P)(-R) EX-Z11A(-P)(-R) EX-Z12FA(-P)(-R) EX-Z12A(-P)(-R) EX-Z13FA(-P)(-R) EX-Z13A(-P)(-R) Item Dark-ON EX-Z11FB(-P)(-R) EX-Z11B(-P)(-R) EX-Z12FB(-P)(-R) EX-Z12B(-P)(-R) EX-Z13FB(-P)(-R) EX-Z13B(-P)(-R) Sensing distance 50 mm 1.969 in 200 mm 7.874 in 500 mm 19.685 in Minimum sensing object ø0.3 mm ø0.012 in opaque object (Completely beam interrupted object) Setting distance between emitter and receiver: 50 mm 1.969 in ø0.5 mm ø0.02 in opaque object (Completely beam interrupted object) Setting distance between emitter and receiver: 200 mm 7.874 in ø1.0 mm ø0.039 in opaque object (Completely beam interrupted object) Setting distance between emitter and receiver: 500 mm 19.685 in Hysteresis ‒ Repeatability (Perpendicular to sensing axis) 0.02 mm 0.001 in or less 0.03 mm 0.001 in or less 0.05 mm 0.002 in or less Supply voltage 12 to 24 V DC ±10 % Ripple P-P 10 % or less Current consumption Emitter: 10 mA or less, Receiver: 10 mA or less Output <NPN output type> NPN open-collector transistor • Maximum sink current: 20 mA • Applied voltage: 30 V DC or less (between output and 0 V) • Residual voltage: 1.5 V or less (at 20 mA sink current) <PNP output type> PNP open-collector transistor • Maximum source current: 20 mA • Applied voltage: 30 V DC or less (between output and +V) • Residual voltage: 1.5 V or less (at 20 mA source current) Short-circuit protection Incorporated Response time 0.5 ms or less Operation indicator Orange LED (Lights up when the sensing output is ON) Stability indicator Green LED (Lights up under the stable light received condition or the stable dark condition) Protection IP67 (IEC) Ambient temperature -10 to +55 °C 14 to +131 °F (No dew condensation or icing allowed), Storage: -30 to +70 °C -22 to +158 °F Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH Ambient illuminance Incandescent light: 5,000 ℓx at the light-receiving face Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 20 MΩ or more, with 250 V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each Shock resistance 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each Light emitting element Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated) Grounding Floating Material Enclosure: PBT, Lens: Polycarbonate, Metallic part: Stainless steel (SUS304) (SUS301 for rear side of front sensing type) Cable (Note 3) 0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long Cable extension Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (both emitter and receiver). Weight Net weight (each emitter and receiver): 15 g approx., Gross weight: 35 g approx. Accessories M2 mounting screws: 1 set (front sensing type: 6 mm 0.236 in in length; side sensing type: 10 mm 0.394 in in length) PRECAUTIONS FOR PROPER USE • Never use this product as a sensing device for personnel protection. • In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23°C 73°F. 2) Model Nos. having the “ -P” are PNP output type and model Nos. having the “-R” are inflection resistant cable type. 3) The inflection resistant cable type has a 0.1 mm2 3-core (thru-beam type emitter: 2-core) flexible cabtyre cable, 2 m 6.562 ft long. Mounting • In case of mounting on tapped holes (Unit: mm in) The tightening torque should be 0.2 N·m or less. • In case of using attached screws and nuts (Unit: mm in) The tightening torque should be 0.2 N·m or less. Side sensing Front sensing Side sensing Front sensing M2 screw (length 10 0.394) (accessory) M2 × 0.4 0.016 hole tapped, 5 0.197 deep 8.5 0.335 Sensing direction 8.5 0.335 Sensing direction M2 × 0.4 0.016 hole tapped, 7 0.276 deep M2 screw (length 6 0.236) (accessory) 8.5 0.335 Sensing direction M2 screw (length 10 0.394) (accessory) Thickness of mounting plate: 2 0.079 or less Nut Spring washer Flat washer 8.5 0.335 Sensing direction Thickness of mounting plate: 2 0.079 or less M2 screw (length 6 0.236) (accessory) Nut Spring washer Flat washer Other • Do not use during the initial transient time (0.5 sec. approx.) after the power supply is switched on. 5 Ultra-minute Photoelectric Sensor EX-Z SERIES |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |