| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
THAT2181A bảng dữ liệu(PDF) 5 Page - THAT Corporation All rights reserved. |
|
|
|||||||||||||||||||||||||||||
THAT2181A bảng dữ liệu(HTML) 5 Page - THAT Corporation All rights reserved. |
|
5 / 12 page ![]() negative control port. Because of the exponential characteristic, the control voltage sets gain linearly in decibels. Figure 6 shows the decibel current gain of a 2181 versus the voltage at Ec+, while Figure 7 shows gain versus the Ec-. Temperature Effects The logging and antilogging in the VCA depends on the logarithmic relationship between voltage and current in a semiconductor junction (in particular, between a transistor's Vbe and IC). As is well known, this relationship is temperature dependent. There- fore, the gain of any log-antilog VCA depends on its temperature. Figure 8 shows the effect of temperature on the negative control port. (The positive control port behaves in the same manner.) Note that the gain at Ec = 0 V is 0 dB, regardless of temperature. Chang- ing temperature changes the scale factor of the gain by 0.33%/°C, which pivots the curve about the 0 dB point. Mathematically, the 2181's gain characteristic is , Eq. 1 Gain = EC+ − EC− (0.0061)(1+0.0033 T) where ∆T is the difference between room temperature (25°C) and the actual temperature, and Gain is the gain in decibels. At room temperature, this reduces to , Eq. 2 Gain = EC+ − EC− 0.0061 If only the positive control port is used, this becomes , Eq. 3 Gain = EC+ 0.0061 If only the negative control port is used, this becomes , Eq. 4 Gain = EC− 0.0061 DC Bias Currents The 2181 current consumption is determined by the resistor between pin 5 (V-) and the negative supply voltage (VEE). Typically, with 15V supplies, the resistor is 5.1 kΩ, which provides approximately 2.4 mA. This current is split into two paths: 570 μA is used for biasing the IC, and the remainder becomes ICELL as shown in Figure 5. ICELL is furth er split in two parts: about 20 μA biases the core transistors (Q1 through Q4), the rest is available for input and output signal current. Trimming The 2181-Series VCAs are intended to be adjusted for minimum distortion by applying a small variable offset voltage to pin 4, the SYM pin. Note that there is a 25 Ω resistor internal to the 2181 between pin 4 and pin 2. As shown in Figure 2, Page 3, the usual method of applying this offset is to use the internal 25 Ω resistor along with a larger value resistor to form a voltage divider connected to the wiper of a trim pot across the supply rails. This trim should be adjusted for minimum harmonic distortion. This is usually done by applying a middle-level, middle-frequency signal (e.g. 1 kHz at 1 V) to the audio input, setting the VCA to 0 dB gain, and adjusting the SYM trim while observing THD at the output. In the 2181, this adjustment coincides closely with the setting which produces minimum control-voltage feedthrough, though the two settings are not always identical. DC Feedthrough Normally, a small dc error term flows in pin 8 (the output). When the gain is changed, the dc term changes. This control-voltage feedthrough is more pronounced with gain; the –A version of the part produces the least feedthrough, the –C version the most. See Figure 9 for typical curves for dc offset vs. gain Audio Performance The 2181-Series VCA design, fabrication and testing ensure extremely good audio performance when used as recommended. The 2181 maintains low distortion over a wide range of gain, cut and signal levels. Figures 10 through 12 show typical distortion performance for representative samples of each grade of the part. At or near unity gain, the 2181 behaves much like a good opamp, with low distortion over the entire audio band. Figure 13 shows typical THD for a 2181A over frequency at 0 dB gain, with a 1 V input signal, while Figure 14 details the harmonic content of the distortion in a typical A–grade part. THAT 2181 Series Page 5 of 12 Document 600030 Rev 02 Blackmer® Trimmable IC VCAs THAT Corporation; 45 Sumner Street; Milford, Massachusetts 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Copyright © 2008, THAT Corporation Figure 9. Representative DC Offset vs. Gain |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |