A22Z-R datasheet(30/40 Pages) OMRON

30 / 40 page

A22NE-P

Connecting Stranded Wires

Use the following procedure to connect the wires to the terminal

block.

1. Hold a flat-blade screwdriver at an angle and insert it into the

release hole.

The angle should be approximately 6

°. If the flat-blade screwdriver

is inserted correctly, you will feel the spring in the release hole.

2. With the flat-blade screwdriver still inserted into the release hole,

insert the wire into the terminal hole until the end strikes the

terminal block.

3. Remove the flat-blade screwdriver from the release hole.

Checking Connections

• After the insertion, pull gently on the wire to make sure that it will

not come off and it is securely fastened to the terminal block.

• If you use a ferrule with a conductor length of 10 mm, part of the

conductor may be visible after the ferrule is inserted into the

terminal block, but the product insulation distance will still be

satisfied.

2. Removing Wires from the Push-In Plus Terminal Block

Use the following procedure to remove wires from the terminal block.

The same method is used to remove stranded wires, solid wires, and

ferrules.

1. Hold a flat-blade screwdriver at an angle and insert it into the

release hole. The angle should be approximately 6

°.

2. With the flat-blade screwdriver still inserted into the release hole,

remove the wire from the terminal insertion hole.

3. Remove the flat-blade screwdriver from the release hole.

3. Recommended Ferrules and Crimp Tools

Coating peeling amount

Recommended ferrules

Note: 1. Make sure that the outer diameter of the wire coating is

smaller than the inner diameter of the insulation sleeve of

the recommended ferrule.

2. Make sure that the ferrule processing dimensions conform

to the following figures.

Recommended Flat-Blade Screwdrivers

Use a flat-blade screwdriver to connect and remove wires.

Use one of the following flat-blade screwdrivers.

The following table shows manufacturers and models as of 2015/Dec.

* The SZF 0-0,4 × 2,5 (manufactured by Phoenix Contact) can be

procured through an OMRON exclusive purchase form (XW4Z-00B).

• After wiring the Switch/Indicator, provide a sufficient insulation

distance.

Approx. 6˚

(2)

Approx. 6˚

(1)

(3)

Flat-blade screwdriver

Approx. 6˚

The wiring and screwdriver angles for the Lighting Unit and Switch

Block (2 contacts) are the same as for the Switch Block (1 contact)

shown in the above illustration.

Approx. 6˚

(2)

Approx. 6˚

(1)

(3)

Flat-blade screwdriver

Approx. 6˚

The wiring and screwdriver angles for the Lighting Unit and Switch

Block (2 contacts) are the same as for the Switch Block (1 contact)

shown in the above illustration.

Recommend Wire Type

Stripping length

(Ferrules not used)

0.25 to 1.5 mm2/AWG 24 to AWG 16

8 mm

Applicable

wire

Ferrule

conductor

length

(mm)

Stripping

length (mm)

(Ferrules not

used)

Recommended ferrules

(mm2)

(AWG)

Phoenix

Contact

product

Weidmuller

product

Wago

product

0.25

AI 0, 25-8

H0.25/12

216-301

AI 0, 25-10

---

0.34

AI 0, 34-8

H0.34/12

216-302

AI 0, 34-10

---

0.5

AI 0, 5-8

H0.5/14

216-201

AI 0, 5-10

H0.5/16

216-241

0.75

AI 0, 75-8

H0.75/14

216-202

AI 0, 75-10

H0.75/16

216-242

1/1.25 18/17

AI 1-8

H1.0/14

216-203

AI 1-10

H1.0/16

216-243

1.25/1.5 17/16

AI 1, 5-8

H1.5/14

216-204

AI 1, 5-10

H1.5/16

216-244

Recommended Crimp Tools

CRIMPFOX6

CRIMPFOX6T-F

CRIMPFOX10S

PZ6 roto

Variocri

mp4

Model

Manufacture

ESD 0,40 × 2,5

Wera

SZS 0,4 × 2,5

SZF 0-0,4 × 2,5

Phoenix Contact

0.4 × 2.5 × 75 302

Wiha

AEF.2,5 × 75

Facom

210-719

Wago

SDI 0,4 × 2,5 × 75

Weidmuller

8 to 10 mm

Max. 1.9 mm

Max. 2.6 mm

Side view

0.4 mm

2.5 mm dia.

2.5 mm

Front view

A22Z-R bảng dữ liệu(PDF) 30 Page - Omron Electronics LLC

A22Z-R bảng dữ liệu(HTML) 30 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

bảng dữ liệu tải về

Link URL