| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
RH850 bảng dữ liệu(PDF) 60 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
RH850 bảng dữ liệu(HTML) 60 Page - Renesas Technology Corp |
|
60 / 68 page ![]() RH850/C1M-A Section 3 Electrical Characteristics Page 60 of 68 R01DS0491EJ0100 Rev.1.00 Mar.31.2025 3.5.3 Error Detect Characteristics Table 3.35 Error Detect Characteristics Error Detect Item Set Threshold (Default Setting) Detect Time Resolver signal error monitor output amplitude voltage*1 Set register RDC3AnDIAG0.EXCETH[7:0] 0.102 × (RVCC±5%) [Vp-p] 220 [µs] (typ.), 2 [ms] (max.) Breaking of resolver signal (Direct current bias supply method) VSINMNT-VCOM or VCOSMNT-VCOM*2 The register used for setting threshold when DC resolver is selected RDC3AnDIAG0.SGBDTH[7:0] COM + 0.35 × (RVCC±5%) [VDC] 10 [ms] (max.) The register used for setting threshold when VR resolver is selected RDC3AnDIAG0.SGBTH[7:0] COM + 0.08 × (RVCC±5%) [VDC] R/D conversion error (over control declination) Recognition level for internal control declination (ε) *3 High side 00CA8H *4 Low side 7F358H Resolver signal power short error Pins S1, S2, S3, and S4 0.9 × (RVCC±5%) [VDC] 0.08 [ms] (max.) Pins RSO and COM 0.8 × (RVCC±5%) [VDC] Resolver signal ground short error Pins S1, S2, S3, and S4 0.1 × (RVCC±5%) [VDC] 0.08 [ms] (max.) Pins RSO and COM 0.2 × (RVCC±5%) [VDC] Sum square amplitude error Integral value of sum square of monitor output amplitude voltage (sin, cos) with an interval within the excitation period High side 0.8 × (RVCC±5%) [Vp-p] *5 Low side 0.2 × (RVCC±5%) [Vp-p] Note 1. Determined as an error, when both of SINMNT and COSMNT become under threshold. Note 2. Determined as an error, when DC level changed over threshold. Note 3. Determined as over, when control declination becomes over high side threshold, or under low side threshold. Note 4. Determined as an error, when control declination recognition rate becomes over 50% as average of period set by the EDPS [1:0] bits in the RDC3AnDIAG1 register (default is about 7.4 ms). It might not be detected, when the error continuous period is shorter than detect period. Note 5. Dependent on the excitation frequency and amplitude error excitation period count settings. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |