8

sensing.honeywell.com

Pressure Range Specifications

PCB Pad Layouts

Table 7. Pressure Range Specifications (continued)

Pressure

Range

(see Figure 3)

Pressure

Range

Unit

Overpressure1

Burst Pressure2

Common Mode

Pressure3

Total Error Band4

(%FSS)

Long-term Stability

1000 hr, 25 °C

(%FSS)

Pmin. Pmax.

1 psi to 150 psi

Differential

001PD

-1

1

psi

10

15

150

±1.5%

±0.25%

005PD

-5

5

psi

30

40

150

±1.5%

±0.25%

015PD

-15

15

psi

60

120

150

±1.5%

±0.25%

030PD

-30

30

psi

120

240

150

±1.5%

±0.25%

060PD

-60

60

psi

250

250

250

±1.5%

±0.25%

Gage

001PG

0

1

psi

10

15

150

±1.5%

±0.25%

005PG

0

5

psi

30

40

150

±1.5%

±0.25%

015PG

0

15

psi

30

60

150

±1.5%

±0.25%

030PG

0

30

psi

60

120

150

±1.5%

±0.25%

060PG

0

60

psi

120

240

250

±1.5%

±0.25%

100PG

0

100

psi

250

250

250

±1.5%

±0.25%

150PG

0

150

psi

250

250

250

±1.5%

±0.25%

1

Overpressure: The maximum pressure which may safely be applied to the product for it to remain in specification once pressure is returned to the operating pressure range. Exposure

to higher pressures may cause permanent damage to the product. Unless otherwise specified this applies to all available pressure ports at any temperature with the operating

temperature range.

2

Burst pressure: The maximum pressure that may be applied to any port of the product without causing escape of pressure media. Product should not be expected to function after

exposure to any pressure beyond the burst pressure.

3

Common mode pressure: The maximum pressure that can be applied simultaneously to both ports of a differential pressure sensor without causing changes in specified

performance.

4

Total Error Band: The maximum deviation from the ideal transfer function over the entire compensated temperature and pressure range. Includes all errors due to offset, full scale

span, pressure non-linearity, pressure hysteresis, repeatability, thermal effect on offset, thermal effect on span, and thermal hysteresis.

Table 8. Pinouts

Output Type

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Digital (I2C, SPI)

GND

V

DD

SS/INT

NC

SDA

SCL

Analog

GND

NC

V

out

NC

NC

V

DD

Figure 4. Recommended PCB Layouts

DIP

SMT

Leadless SMT

5,00

[0.197]

6,00

[0.236]

2,54

[0.1]

2,73

[0.107]

8,00

[0.315]

11,00

[0.433]

8,85

[0.348]

12,35

[0.315]

1

2

3

65

4

0,65

[0.026]

Gage reference hole: do not plug

11,0

[0.433]

12

3

6

54

5,00

[0.197]

6,00

[0.236]

6X

ø0.73

[0.029]

2,54

[0.1]

2,73

[0.107]

8,00

[0.315]

11,25

[0.443]

Gage reference hole: do not plug

7,00

[0.28]

3,00

[0.118]

2,50

[0.098]

2,73

[0.107]

8,00

[0.315]

4,00

[0.157]

3,25

0.128]

8,00

[0.315]

1,30

[0.051]

12

3

65

4

Gage reference hole: do not plug