TMUX741xF ±60 V Fault-Protected, 1:1 (SPST), 4-Channel Switches

With Latch-Up Immunity and 1.8-V Logic

1 Features

• Wide supply voltage range:

– Single supply: 8 V to 44 V

– Dual supply: ±5 V to ±22 V

• Integrated fault protection:

– Overvoltage protection, source to supplies or

source to drain: ±85 V

– Overvoltage protection: ±60 V

– Powered-off protection: ±60 V

– Interrupt flags to indicate fault status

– Output open circuited during fault

• Latch-up immunity by device construction

• Human Body Model (HBM) ESD rating: 6-kV

• Low on-resistance: 8.3 Ω typical

• Flat on-resistance: 10 mΩ typical

• Logic capable: 1.8-V

• Fail-safe logic: up to 44 V independent of supply

• Industry-standard TSSOP and smaller WQFN

packages

2 Applications

• Factory automation and control

• Programmable logic controllers (PLC)

• Analog input modules

• Semiconductor test equipment

• Battery test equipment

• Servo drive control module

• Data acquisition systems (DAQ)

3 Description

The TMUX7411F, TMUX7412F, and TMUX7413F

are

complementary

metal-oxide

semiconductor

(CMOS) analog switches in 1:1 (SPST), 4-channel

configurations. The devices work well with dual

supplies (±5 V to ±22 V), a single supply (8 V to

44 V), or asymmetric supplies (such as VDD = 12 V,

VSS = –5 V). The overvoltage protection is available

in powered and powered-off conditions, making

the TMUX741xF devices suitable for applications

where power supply sequencing cannot be precisely

controlled.

The devices block fault voltages up to +60 V or

−60 V relative to ground in powered and powered-off

conditions. When no power supplies are present, the

switch channels remain in the OFF state regardless

of the switch input conditions, and any control signal

present on the logic pins is ignored. If the signal

path input voltage on any Sx pin exceeds the supply

voltage (VDD or VSS) by a threshold voltage (VT), the

channel turns OFF and the Sx pin becomes high

impedance. The drain pin (Dx) of a selected channel

under a fault condition is floating. The TMUX741xF

devices provide an active-low interrupt flag (FF) to

indicate if any of the source inputs are experiencing a

fault condition to help system diagnostics.

Package Information(1)(3)

PART NUMBER

PACKAGE

BODY SIZE (NOM)

TMUX7411F

TMUX7412F

TMUX7413F

PW (TSSOP, 16) (2)

5.00 mm × 4.40 mm

RRP (WQFN, 16)

4.00 mm × 4.00 mm

(1)

For all available packages, see the orderable addendum at

the end of the data sheet.

(2)

Preview package.

(3)

See Device Comparison Table

SW

SW

S1

S2

VDD

VSS

TMUX7411F

(SELx = Logic 1)

Fault Detection/

Switch Driver/

Logic Decoder

SEL1

SEL2

SEL3

SW

SW

S3

S4

D1

D2

D3

D4

FF

SEL4

S1

S2

VDD

VSS

Fault Detection/

Switch Driver/

Logic Decoder

SEL1

SEL2

SEL3

S3

S4

D1

D2

D3

D4

FF

SEL4

SW

SW

SW

SW

TMUX7412F

(SELx = Logic 1)

S1

S2

VDD

VSS

Fault Detection/

Switch Driver/

Logic Decoder

SEL1

SEL2

SEL3

S3

S4

D1

D2

D3

D4

FF

SEL4

SW

SW

TMUX7413F

(SELx = Logic 1)

SW

SW

Functional Block Diagram

TMUX7411F, TMUX7412F, TMUX7413F

SCDS404B – MARCH 2021 – REVISED NOVEMBER 2022

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION

DATA.