L99DZ80EP datasheet(11/68 Pages) STMICROELECTRONICS

11 / 68 page

DocID18260 Rev 6

11/68

L99DZ80EP

Electrical specifications

2.1

Absolute maximum ratings

Stressing the device above the rating listed in the “Absolute maximum ratings” table may

cause permanent damage to the device. These are stress ratings only and operation of the

device at these or any other conditions above those indicated in the operating sections of

this specification is not implied. Exposure to Absolute Maximum Rating conditions for

extended periods may affect device reliability. Refer also to the STMicroelectronics SURE

Program and other relevant quality document.

Table 3. Absolute maximum ratings

Symbol

Parameter/test condition

Value

[DC Voltage]

Unit

VS1, VS2

DC supply voltage

-0.3 to +28

Single pulse / tmax < 400 ms “transient load dump”

-0.3 to +40

VCC

Stabilized supply voltage, logic supply

-0.3 to VS +0.3

VDI, VCLK, VCSN, VDO,

VCM, VDIR, VPWMH, VDIR

Logic input / output voltage range

-0.3 to VCC +0.3

VOUTn, ECDR, ECV, ECFD Output voltage (n = 1 to 11)

-0.3 to VS +0.3

VSL1, VSH1, VSL2, VSH2

(VSxy)

High voltage signal pins

-6 to 40

VGL1, VGH1, VGL2, VGH2

(VGxy)

High voltage signal pins

VSxy - 1 to VSxy +10;

VCP +0.3

VCP1P

High voltage signal pins

VS - 0.3 to VS +10

VCP2P

High voltage signal pins

VS - 0.6 to VS +10

VCP1M, VCP2M

High voltage signal pins

-0.3 to VS +0.3

VCP

High voltage signal pin

VS1,2 26 V

VS - 0.3 to VS +14

VS1,2 > 26 V

VS - 0.3 to +40

IOUT2,3,9,10, ECV, ECFD

Output current(1)

±1.25

IOUT1,6,7

Output current(1) (low on-resistance mode)

±5

IOUT7

Output current(1) (high on-resistance mode)

±5

IOUT8

Output current(1)

±2.5

IOUT4,5

Output current(1)

±10

IOUT11

Output current(1)

±7.5

IVS1cum

Maximum cumulated input current at VS1 pins

(1)

±12.5

IVS2cum

Maximum cumulated input current at VS2 pins

(1)

±12.5

IGND1cum

Maximum cumulated output current at GND1 pins

(1)

±5

IGND2cum

Maximum cumulated output current at GND2 pins

(1)

±12.5

Values for the absolute maximum DC current through the bond wires. This value does not consider maximum power

dissipation or other limits.

L99DZ80EP bảng dữ liệu(PDF) 11 Page - STMicroelectronics

L99DZ80EP bảng dữ liệu(HTML) 11 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

bảng dữ liệu tải về

Link URL