| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STM32U073M8T6TR bảng dữ liệu(PDF) 44 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32U073M8T6TR bảng dữ liệu(HTML) 44 Page - STMicroelectronics |
|
44 / 146 page ![]() Table 20. Current characteristics Symbol Ratings Max Unit ∑IVDD Total current into sum of all VDD power lines (source)(1) 140 mA ∑IVSS Total current out of sum of all VSS ground lines (sink) 140 IVDD(PIN) Maximum current into each VDD power pin (source) 100 IVSS(PIN) Maximum current out of each VSS ground pin (sink) 100 IIO(PIN) Output current sunk by any I/O and control pin except FT_f 20 Output current sunk by any FT_f pin 20 Output current sourced by any I/O and control pin 20 ∑IIO(PIN) Total output current sunk by sum of all I/Os and control pins(2) 100 Total output current sourced by sum of all I/Os and control pins(2) 100 IINJ(PIN)(3) Injected current on FT_xxx, TT_xx, RST -5/+0(4) ∑|IINJ(PIN)| Total injected current (sum of all I/Os and control pins) 25 1. All main power (VDD, VDDA, VDDUSB, VBAT) and ground (VSS, VSSA) pins must always be connected to the external power supplies, in the permitted range. 2. This current consumption must be correctly distributed over all I/Os and control pins. The total output current must not be sunk/sourced between two consecutive power supply pins. 3. Positive injection (when VIN > VDDIOx) is not possible on these I/Os and does not occur for input voltages lower than the specified maximum value. 4. A negative injection is induced by VIN < VSS. IINJ(PIN) must never be exceeded. Refer also to Table 19. Voltage characteristics for the maximum allowed input voltage values. 5. When several inputs are submitted to a current injection, the maximum ∑|IINJ(PIN)| is the absolute sum of the negative injected currents (instantaneous values). Table 21. Thermal characteristics Symbol Ratings Value Unit TSTG Storage temperature range -65 to +150 °C TJ Maximum junction temperature 150 °C 6.3 Operating conditions 6.3.1 General operating conditions Table 22. General operating conditions Symbol Parameter Conditions Min Max Unit fHCLK Internal AHB clock frequency - 0 56 MHz fPCLK Internal APB clock frequency - 0 56 VDD Standard operating voltage - 1.71(1) 3.6 V VDDA Analog supply voltage ADC or COMP used 1.62 3.6 OPAMP used 1.8 ADC, OPAMP, COMP not used 0 VBAT Backup domain supply voltage - 1.55 3.6 VDDUSB USB supply voltage USB used 3.0 3.6 V STM32U073x8/B/C Electrical characteristics DS14548 - Rev 2 page 44/146 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |