công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

ISL81801EVAL2Z bảng dữ liệu(PDF) 38 Page - Renesas Technology Corp

tên linh kiện ISL81801EVAL2Z
Giải thích chi tiết về linh kiện  80V Bidirectional 4-Switch Synchronous Buck-Boost Controller
PDF  50 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  RENESAS [Renesas Technology Corp]
Trang chủ  http://www.renesas.com
Logo RENESAS - Renesas Technology Corp

ISL81801EVAL2Z bảng dữ liệu(HTML) 38 Page - Renesas Technology Corp

Back Button ISL81801EVAL2Z Datasheet HTML 34Page - Renesas Technology Corp ISL81801EVAL2Z Datasheet HTML 35Page - Renesas Technology Corp ISL81801EVAL2Z Datasheet HTML 36Page - Renesas Technology Corp ISL81801EVAL2Z Datasheet HTML 37Page - Renesas Technology Corp ISL81801EVAL2Z Datasheet HTML 38Page - Renesas Technology Corp ISL81801EVAL2Z Datasheet HTML 39Page - Renesas Technology Corp ISL81801EVAL2Z Datasheet HTML 40Page - Renesas Technology Corp ISL81801EVAL2Z Datasheet HTML 41Page - Renesas Technology Corp ISL81801EVAL2Z Datasheet HTML 42Page - Renesas Technology Corp Next Button
Zoom Inzoom in Zoom Outzoom out
 38 / 50 page
background image
ISL81801
5. Functional Description
FN8937 Rev.1.4
Page 38 of 49
Mar 8, 2024
circuit. The buffer output is connected to the iSh bus using R28 in Converter 1 and R61 in Converter 2 to create the
reference signal. The voltage on the iSh bus, ViSh, is calculated using Equation 16.
where VIMON_OUT1 is the Converter 1 IMON_OUT pin voltage and VIMON_OUT2 is the Converter 2 IMON_OUT pin
voltage.
The second op amp, U2A in Converter 1 or U4A in Converter 2 is a differential op amp to feed the current error
signal to the IC FB_OUT pin. The differential input signal is equal to VIMON_OUT1 - ViSh for U2A and
VIMON_OUT2 -ViSh for U4A. The differential op amp gain and the value of the resistor between the op amp output
and the FB_OUT pin is defined based on the current sharing accuracy and the allowed maximum output voltage
change caused by the current sharing loop, assuming the current sense circuit tolerance is ignored.
The maximum allowed current sharing error is represented by the maximum allowed differential op amp input.
The differential op amp outputs a maximum voltage of 5V at its maximum differential input, assuming a rail-to-rail
op amp is used. The differential op amp gain Ksh is calculated using Equation 17.
where ΔVsh is the maximum allowed differential op amp input voltage, which is proportional to the output current
sharing error ΔIsh = |IOUT1 – IOUT2| / 2. IOUT1 and IOUT2 are the output currents of Converter 1 and 2, respectively.
ΔVsh = ΔIsh x RIM_OUT x RS_OUT x GmISEN, referring to the descriptions in Input and Output Average Current
Monitoring and Regulation Loops.
As shown in Figure 54, Ksh = R23/R27 for Converter 1 and Ksh = R56/R58 for Converter 2.
The value Rsh of the resistor between the differential op amp output and the FB_OUT pin is calculated using
Equation 18.
where ΔVOUT is the maximum allowed output voltage change caused by the current sharing loop, which is limited
by the VOUT regulation tolerance.
RFBO1 is the resistance of the upper resistor of the VOUT voltage sense divider shown in Figure 43. As shown in
Figure 54, Rsh = R29 + R30 for Converter 1 and Rsh = R64 + R65 for Converter 2. RFBO1 = R18 for Converter 1 and
RFBO1 = R50 for Converter 2.
5.13 Gate Drivers
The ISL81801 integrates two almost identical high voltage driver pairs to drive both buck and boost MOSFET
pairs. Each driver pair consists of a gate control logic circuit, a low-side driver, a level shifter, and a high-side
driver.
The ISL81801 incorporates an adaptive dead time algorithm that optimizes operation with varying MOSFET
conditions. This algorithm provides approximately 16ns dead time between the switching of the upper and lower
MOSFETs. This dead time is adaptive and allows operation with different MOSFETs without having to externally
adjust the dead time using a resistor or capacitor. During turn-off of the lower MOSFET, the LGATE voltage is
monitored until it reaches a threshold of 1V, at which time the UGATE is released to rise. Adaptive dead time
circuitry monitors the upper MOSFET gate voltage during UGATE turn-off. When the upper MOSFET
gate-to-source voltage drops below a threshold of 1V, the LGATE is allowed to rise. Renesas recommends
against using a resistor between the driver outputs and the respective MOSFET gates, because it can interfere
with the dead time circuitry.
The low-side gate driver is supplied from VDD and provides a 3A peak sink and 2A peak source current. The
high-side gate driver can also deliver peak 3A sink and 2A source current. Gate-drive voltage for the upper
(EQ. 16)
ViSh
VIMON_OUT1 VIMON_OUT2
+
 2
=
(EQ. 17)
Ksh
5
Vsh
--------------
=
(EQ. 18)
Rsh
5RFBO1
VOUT
-----------------------------
=



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com