LP5562TMXSLASHNOPB datasheet(18/52 Pages) TI2

18 / 52 page

PWM Control

Value

Current value

Step time = 31.2 ms

End of 1st Ramp command,

start next command

Steps

End of 2nd Ramp command,

start next command

Rising ramp,

Sign = 0

Downward

ramp, Sign = 1

Increment = 4

=> 5 cycles

SVA-30197407

LP5562

SNVS820B – APRIL 2013 – REVISED DECEMBER 2016

www.ti.com

Product Folder Links: LP5562

Submit Documentation Feedback

7.3.3.4.1

Ramp/Wait

The ramp command generates a PWM ramp starting from current value. At each ramp step the output is

incremented by one. Time for one step is defined with Prescale and Step time bits. Minimum time for one step is

0.49 ms and maximum time is 63 × 15.6 ms = 1 second/step, so it is possible to program very fast and also very

slow ramps. Increment value defines how many steps are taken in one command. Number of actual steps is

Increment + 1. Maximum value is 127d, which corresponds to half of full-scale (128 steps). If during ramp

command PWM reaches minimum/maximum (0/255) ramp command will be executed to the end and PWM will

stay at minimum/maximum. This enables the ramp command to be used as combined ramp and wait command

in a single instruction.

The ramp command can be used as wait instruction when increment is zero.

Setting register 00h bit LOG_EN sets the scale as either linear to logarithmic. When LOG_EN = 0, linear scale is

used, and when LOG_EN = 1, logarithmic scale is used. By using logarithmic scale the visual effect of the ramp

command seems linear to the eye.

Table 10. Ramp/Wait Command

Ramp/Wait command

Pre-

scale

Step time

Sign

Increment

Table 11. Ramp/Wait Command Bits

NAME

VALUE(d)

DESCRIPTION

Prescale

Divides master clock (32.768 Hz) by 16 = 2048 Hz, 0.49 ms cycle time

Divides master clock (32.768 Hz) by 512 = 64 Hz, 15.6 ms cycle time

Step time

1-63

One ramp increment done in (step time) x (clock after prescale) Note: 0 means set PMW

command.

Sign

Increase PWM output

Decrease PWM output

Increment

0-127

The number of steps is Increment + 1. Note: 0 is a wait instruction.

For example, if following parameters are used for ramp:

•

Prescale = 1

≥ cycle time = 15.6 ms

•

Step time = 2

≥ time = 15.6 ms × 2 = 31.2 ms

•

Sign = 0

≥ rising ramp Increment = 4 ≥ 5 cycles

Ramp command will be: 0100 0010 0000 0100b = 4204h

If current PWM value is 3, and the first command is as described above, the next command is a ramp with

otherwise same the parameters, but with Sign = 1 (Command = 4284h), the result will be like in the following

figure:

Figure 16. Example of 2 Sequential Ramp Commands

LP5562TMX/NOPB bảng dữ liệu(PDF) 18 Page - Texas Instruments

LP5562TMX/NOPB bảng dữ liệu(HTML) 18 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

bảng dữ liệu tải về

Link URL