PFS7523LSLASHH datasheet(21/37 Pages) POWERINT

21 / 37 page

Rev. D 04/25

PFS7523-7529/7533-7539

www.power.com

Parameter

Symbol

Conditions

SOURCE = 0 V; V

CC = 12 V,

-40 °C < T

J(C) < 125 °C (Note C)

(Unless Otherwise Specified)

Min

Typ

Max

Units

Currents

Undervoltage Current

Consumption After

Power-Up of Core and

Zeners

CC(UVLO)

VCC < UVLO+(min)

V = 1 V, C = 0 V, FB = 3.85 V

0 °C < T

J(C) < 100 °C

VCC

140

Standby Current

Consumption – No

Switching Prior to

Brown-In

CC(STBY)

V = 1 V, C = 0 V, FB = 3.85 V

0 °C < T

J(C) < 100 °C

VCC

320

Current Consumption

– in Burst Mode,

No Switching

CC(BURST)

FB = 3.85 V, C < V

ERR_MIN,

V = 1.414 V

(or 2.828 V for High-Line Only Parts)

0 °C < T

J(C) < 100 °C

VCC

395

470

Absolute Maximum Ratings(1,2)

DRAIN Pin Peak Current: PFS7523/PFS7533 .............................7.5 A

PFS7524/PFS7534 ............................ 9.0 A

PFS7525/PFS7535 ...........................11.3 A

PFS7526/PFS7536 ...........................13.5 A

PFS7527/PFS7537............................15.8 A

PFS7528/PFS7538 ...........................18.0 A

PFS7529/PFS7539 ...........................21.0 A

DRAIN Pin Voltage .................................... -0.3 V to 530 V / 540 V(6)

VCC(3) Pin Voltage .................................................... -0.3 V to 17.5 V

PG ......................................................................... -0.3 V to 17.5 V

PG Pin Current.......................................................................10 mA

V, PGT, FB, C, REF Pin Voltage ...................................-0.3 V to 5.6 V

Storage Temperature .............................................-65 °C to 150 °C

Junction Temperature(4)...........................................-40 °C to 150 °C

Lead Temperature(5) ............................................................. 260 °C

Notes:

1. All voltages referenced to SOURCE, T

A = 25 °C.

2. Maximum ratings specified may be applied one at a time without

causing permanent damage to the product. Exposure to Absolute

Maximum Ratings conditions for extended periods of time may

affect product reliability.

3. The absolute maximum rating of the VCC is 17.5 V. This is an

absolute maximum condition that must not be exceeded. Voltages

between the max operating voltage (15 V) and this abs max

rating should be very infrequent and short in duration (e.g. at

start-up or temporary fault conditions). It is not intended as a

guarantee of the reliability of the product up to the absolute

maximum rating, but is a guideline as to the level of applied

voltage above which there is a risk of immediate damage to the

product.

4. Normally limited by internal circuitry. Applies to Controller T

J(C),

MOSFET T

J(M) and Diode Junction Temperature TJ(D).

5. 1/16” from case for 5 seconds.

6. Duration less than 15 ns and I

DS ≤ IOCP(TYP).

7. T

C(D) diode case temperature.

Thermal Resistance

Thermal Resistance: H/L Package:

JA)

(1)

..................................................... 103 °C/W

JC) .............................................. (see Figure 22)

Notes:

1. Controller junction temperature (T

J(C)) may be less than the

MOSFET Junction Temperature (T

J(M)) and Diode Junction

Temperature (T

J(D)).

Qspeed Diode

PFS7523-7529

PFS7533-7535

PFS7536-7539

Peak Repetitive Reverse Voltage (VRRM)

530 V

Average Forward Current IF(AV)

J(D) = 150 °C

3 A

6 A

Non-Repetitive Peak Surge Current (IFSM)

60 Hz, ½ cycle, T

C(D)

(7)

= 25 °C

50 A

100 A

Non-Repetitive Peak Surge Current (IFSM)

t = 500 µs, T

C(D)

(7)

= 25 °C

130 A

260 A

PFS7523L/H bảng dữ liệu(PDF) 21 Page - Power Integrations, Inc.

PFS7523L/H bảng dữ liệu(HTML) 21 Page - Power Integrations, Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

bảng dữ liệu tải về

Link URL