công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

TPS2145IPWPR bảng dữ liệu(PDF) 15 Page - Texas Instruments

tên linh kiện TPS2145IPWPR
Giải thích chi tiết về linh kiện  LDO AND DUAL SWITCH WITH CONTROLLED RISE TIMES FOR DSP AND PORTABLE APPLICATIONS
PDF  34 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  TI [Texas Instruments]
Trang chủ  http://www.ti.com
Logo TI - Texas Instruments

TPS2145IPWPR bảng dữ liệu(HTML) 15 Page - Texas Instruments

Back Button TPS2145IPWPR Datasheet HTML 11Page - Texas Instruments TPS2145IPWPR Datasheet HTML 12Page - Texas Instruments TPS2145IPWPR Datasheet HTML 13Page - Texas Instruments TPS2145IPWPR Datasheet HTML 14Page - Texas Instruments TPS2145IPWPR Datasheet HTML 15Page - Texas Instruments TPS2145IPWPR Datasheet HTML 16Page - Texas Instruments TPS2145IPWPR Datasheet HTML 17Page - Texas Instruments TPS2145IPWPR Datasheet HTML 18Page - Texas Instruments TPS2145IPWPR Datasheet HTML 19Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 15 / 34 page
background image
TPS2145, TPS2147
TPS2155, TPS2157
SLVS333 − AUGUST 2001
15
www.ti.com
TYPICAL CHARACTERISTICS
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
−40 −25 −10
5
20
35
50
65
UNDERVOLTAGE LOCKOUT
vs
JUNCTION TEMPERATURE
TJ − Junction Temperature − °C
Rising
Falling
80
95 110
Figure 17
APPLICATION INFORMATION
external capacitor requirements on power lines
Ceramic bypass capacitors (0.01-
µ to 0.1-µ) between VIN/SWIN1 and GND and SWIN2 and GND, close to the
device, are recommended to improve load transient response and noise rejection.
Bulk capacitors ( 4.7-
µF) between VIN/SWIN1 and GND and between SWIN2 and GND are also recommended,
especially if load transients in the hundreds of milliamps with fast rise times are anticipated.
A 66-
µF bulk capacitor is recommended from OUTx to ground, especially when the output load is heavy. This
precaution helps reduce transients seen on the power rails. Additionally, bypassing the outputs with a 0.1-
µF
ceramic capacitor improves the immunity of the device to short-circuit transients.
LDO output capacitor requirements
Stabilizing the internal control loop requires an output capacitor connected between LDO_OUT and GND. The
minimum recommended capacitance is a 4.7
µF with an ESR value between 200 mΩ and 10 Ω. Solid tantalum
electrolytic, aluminum electrolytic and multilayer ceramic capacitors are all suitable, provided they meet the
ESR requirements.
The adjustable LDO (for voltages lower than 3 V) requires a bypass capacitor across the feedback resistor as
shown in Figure 18. The value of this capacitor is determined by using the following equation:
C
f
+
1
(63.7e3
2
3.14
R1)
* 4pf
where R1 is derived by programming the adjustable LDO (see programming the adjustable LDO regulator
section shown below).
(1)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com