| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STM32F412XE bảng dữ liệu(PDF) 83 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32F412XE bảng dữ liệu(HTML) 83 Page - STMicroelectronics |
|
83 / 201 page ![]() DocID028087 Rev 7 83/201 STM32F412xE/G Electrical characteristics 166 PD Power dissipation at TA = 85°C for range 6 or TA = 105°C for range 7(8) UFQFPN48 - - 625 mW WLCSP64 - - 392 LQFP64 - - 425 LQFP100 - - 465 LQFP144 - - 571 UFBGA100 - - 351 UFBGA144 - - 416 PD Power dissipation at TA = 125 °C for range 3(8) UFQFPN48 - - 156 WLCSP64 - - 98 LQFP64 - - 106 LQFP100 - - 116 LQFP144 - - 142 UFBGA100 - - 88 UFBGA144 - - 104 TA Ambient temperature for range 6 Maximum power dissipation -40 - 85 °C Low power dissipation(9) -40 - 105 Ambient temperature for range 7 Maximum power dissipation -40 - 105 Low power dissipation(9) -40 - 125 Ambient temperature for range 3 Maximum power dissipation -40 - 110 Low power dissipation(9) -40 - 130 TJ Junction temperature range Range 6 -40 - 105 Range 7 -40 - 125 Range 3 -40 - 130 1. VDD/VDDA minimum value of 1.7 V with the use of an external power supply supervisor (refer to Section 3.18.2: Internal reset OFF). 2. When the ADC is used, refer to Table 72: ADC characteristics. 3. If VREF+ pin is present, it must respect the following condition: VDDA-VREF+ < 1.2 V. 4. It is recommended to power VDD and VDDA from the same source. A maximum difference of 300 mV between VDD and VDDA can be tolerated during power-up and power-down operation. 5. Only the DM (PA11) and DP (PA12) pads are supplied through VDDUSB. For application where the VBUS (PA9) is directly connected to the chip, a minimum VDD supply of 2.7V is required. (some application examples are shown in appendix B) 6. Guaranteed by test in production 7. To sustain a voltage higher than VDD+0.3, the internal Pull-up and Pull-Down resistors must be disabled 8. If TA is lower, higher PD values are allowed as long as TJ does not exceed TJmax. 9. In low power dissipation state, TA can be extended to this range as long as TJ does not exceed TJmax. Table 16. General operating conditions (continued) Symbol Parameter Conditions Min Typ Max Unit |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |