| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
S25FL256SDPNFAQ bảng dữ liệu(PDF) 109 Page - Cypress Semiconductor |
|
|
|||||||||||||||||||||||||||||
S25FL256SDPNFAQ bảng dữ liệu(HTML) 109 Page - Cypress Semiconductor |
|
109 / 149 page ![]() Document Number: 001-98283 Rev. *M Page 108 of 148 S25FL128S/S25FL256S Figure 73. Sector Erase Command Sequence (ExtAdd = 0, 3-Byte Address, D8h) Figure 74. Sector Erase Command Sequence (ExtAdd = 1, D8h or 4-Byte Address, DCh) 9.6.3 Bulk Erase (BE 60h or C7h) The Bulk Erase (BE) command sets all bits to 1 (all bytes are FFh) inside the entire flash memory array. Before the BE command can be accepted by the device, a Write Enable (WREN) command must be issued and decoded by the device, which sets the Write Enable Latch (WEL) in the Status Register to enable any write operations. CS# must be driven into the logic high state after the eighth bit of the instruction byte has been latched in on SI. This will initiate the erase cycle, which involves the pre-programming and erase of the entire flash memory array. If CS# is not driven high after the last bit of instruction, the BE operation will not be executed. As soon as CS# is driven into the logic high state, the erase cycle will be initiated. With the erase cycle in progress, the user can read the value of the Write-In Progress (WIP) bit to determine when the operation has been completed. The WIP bit will indicate a 1 when the erase cycle is in progress and a 0 when the erase cycle has been completed. A BE command can be executed only when the Block Protection (BP2, BP1, BP0) bits are set to 0’s. If the BP bits are not zero, the BE command is not executed and E_ERR is not set. The BE command will skip any sectors protected by the DYB or PPB and the E_ERR status will not be set. Figure 75. Bulk Erase Command Sequence 1 3 2 10 9 8 7 6 5 4 0 31 30 29 28 Instruction 24 Bit Address 23 21 22 1 3 2 0 SCK SI MSB CS # 1 3 2 1 0 9 8 7 6 5 4 0 3 9 3 8 3 7 3 6 In s tru c tio n 3 2 B it A d d re s s 3 1 2 9 3 0 1 3 2 0 S C K S I M S B C S # 3 27 6 5 4 0 Instruction SCK SI 1 CS# |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |