công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

LMH6628MA/NOPB bảng dữ liệu(PDF) 13 Page - Texas Instruments

tên linh kiện LMH6628MA/NOPB
Giải thích chi tiết về linh kiện  LMH6628 Dual Wideband, Low Noise, Voltage Feedback Op Amp
PDF  24 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  TI2 [Texas Instruments]
Trang chủ  https://www.ti.com
Logo TI2 - Texas Instruments

LMH6628MA/NOPB bảng dữ liệu(HTML) 13 Page - Texas Instruments

Back Button LMH6628MA/NOPB Datasheet HTML 9Page - Texas Instruments LMH6628MA/NOPB Datasheet HTML 10Page - Texas Instruments LMH6628MA/NOPB Datasheet HTML 11Page - Texas Instruments LMH6628MA/NOPB Datasheet HTML 12Page - Texas Instruments LMH6628MA/NOPB Datasheet HTML 13Page - Texas Instruments LMH6628MA/NOPB Datasheet HTML 14Page - Texas Instruments LMH6628MA/NOPB Datasheet HTML 15Page - Texas Instruments LMH6628MA/NOPB Datasheet HTML 16Page - Texas Instruments LMH6628MA/NOPB Datasheet HTML 17Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 24 page
background image
LMH6628
www.ti.com
SNOSA02D – MAY 2002 – REVISED MARCH 2013
A current source, built around Q1, provides the necessary bias current for the second amplifier and prevents
saturation when power is applied. The resistor, R, closes the loop while diode D2 prevents negative saturation
when VIN is less than VC. A MOS-type switch (not shown) can be used to reset the capacitor's voltage.
The maximum speed of detection is limited by the delay of the op amps and the diodes. The use of Schottky
diodes will provide faster response.
ADJUSTABLE OR BANDPASS EQUALIZER
A "boost" equalizer can be made with the LMH6628 by summing a bandpass response with the input signal, as
shown in Figure 34.
Figure 34. "Boost" Equalizer Made With the LMH6628 by Summing a Bandpass Response With the Input
Signal
The overall transfer function is shown in Equation 4.
(4)
To build a boost circuit, use the design equations Equation 5 and Equation 6.
(5)
(6)
Select R2 and C using Equation 5. Use reasonable values for high frequency circuits - R2 between 10Ω and 5kΩ,
C between 10pF and 2000pF. Use Equation 6 to determine the parallel combination of Ra and Rb. Select Ra and
Rb by either the 10Ω to 5kΩ criteria or by other requirements based on the impedance Vin is capable of driving.
Finish the design by determining the value of K from Equation 7.
(7)
Figure 35 shows an example of the response of the circuit of Figure 34, where fo is 2.3MHz. The component
values are as follows: Ra=2.1kΩ, Rb = 68.5Ω, R2 = 4.22kΩ, R = 500Ω, KR = 50Ω, C = 120pF.
Copyright © 2002–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LMH6628



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com