| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM3463SQ/NOPB bảng dữ liệu(PDF) 21 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
LM3463SQ/NOPB bảng dữ liệu(HTML) 21 Page - Texas Instruments |
|
21 / 43 page ![]() VLED-MAX-COLD, the highest forward voltage of LED strings under low temperature Identify VLED-MAX-COLD Identify VLED-MIN-HOT Adjust the nominal output voltage of the primary power supply, VRAIL(nom) = VLED-MIN-HOT - 5V Set the peak output voltage of the primary power supply (at VOutP = 0.15V), VRAIL(peak) = VLED-MAX-COLD + 10V Set the LED turn on voltage, VDHC_READY = VLED-MAX-COLD + 5V Begin design End of design VLED-MIN-HOT, the lowest forward voltage of LED strings under high temperature VRAIL(nom), the nominal output voltage of the primary power supply. e.g. Assume VFB = 2.5V, REMARKS PROCEDURES VRAIL(peak), the output voltage of the primary power supply when the OutP pin is pulling to its minimum. VFB R2 VFB - 0.15 - 0.6 RDHC VFB R1 VRAIL(peak) = R1 + R2 R2 2.5V VRAIL(nom) = VDHC_READY, the LED turn on voltage is defined by RFB1 and RFB2 connected to the VLedFB pin. RFB1 + RFB2 RFB2 2.5V VDHC_READY = LM3463 www.ti.com SNVS807A – MAY 2012 – REVISED MAY 2013 Figure 26. Procedure of defining startup parameters Setting the RDHC and VRAIL Prior to defining the parameters for the operations in steady state, the value of the RDHC and different levels of the supply rail voltage (VRAIL) during system startup must be determined. Figure 26 illustrates the procedures of determining the value of the RDHC and voltage levels of the VRAIL(nom), VRAIL(peak) and VDHC_READY. In Figure 26, the VLED-MAX-COLD and VLED-MIN-HOT are the maximum and minimum forward voltages of the LED strings under the required lowest and highest operation temperatures respectively. In order to ensure all the LED string are supplied with adequate forward current when turning on the LEDs, the VDHC_READY must be set higher than the VLED-MAX-COLD. For most applications, the VDHC_READY can be set 5 V higher than the VLED-MAX-COLD. In order to reserve voltage headroom to perform DHC under high operation temperature, the nominal output voltage of the primary power supply must be set lower than the VLED-MIN-HOT. For most applications, the VRAIL(nom) can be set 5 V lower than the VLED-MIN-HOT. Figure 27 shows an example connection diagram of interfacing the LM3463 to a power supply of 2.5V feedback reference voltage. Copyright © 2012–2013, Texas Instruments Incorporated Submit Documentation Feedback 21 Product Folder Links: LM3463 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |