AOD407

Symbol

Min

Typ

Max

Units

BVDSS

-60

V

-0.003

-1

TJ=55°C

-5

IGSS

±100

nA

VGS(th)

-1.5

-2.1

-3

V

ID(ON)

-30

A

91

115

TJ=125°C

150

114

150

m

W

gFS

12.8

S

VSD

-0.76

-1

V

IS

-12

A

Ciss

987

pF

Coss

114

pF

Crss

46

pF

Rg

9.5

15

W

Qg(10V)

15.8

22

nC

Qg(4.5V)

7.4

12

nC

Qgs

3

nC

Qgd

3.5

nC

tD(on)

9

ns

tr

10

ns

tD(off)

25

ns

tf

11

ns

trr

27.5

ns

Qrr

30

nC

THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL

COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING

OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,

FUNCTIONS AND RELIABILITY WITHOUT NOTICE

Maximum Body-Diode Continuous Current

Input Capacitance

Output Capacitance

Turn-On DelayTime

DYNAMIC PARAMETERS

VGS=0V, VDS=-30V, f=1MHz

Gate Drain Charge

Total Gate Charge (10V)

VGS=-10V, VDS=-30V, ID=-12A

Turn-On Rise Time

Turn-Off DelayTime

VGS=-10V, VDS=-30V, RL=2.5W,

RGEN=3W

Gate resistance

VGS=0V, VDS=0V, f=1MHz

Turn-Off Fall Time

SWITCHING PARAMETERS

Total Gate Charge (4.5V)

Gate Source Charge

Forward Transconductance

Diode Forward Voltage

m

W

VGS=-4.5V, ID=-8A

IS=-1A,VGS=0V

VDS=-5V, ID=-12A

VDS=0V, VGS=±20V

Zero Gate Voltage Drain Current

Gate-Body leakage current

RDS(ON)

Static Drain-Source On-Resistance

IF=-12A, dI/dt=100A/ms

Electrical Characteristics (TJ=25°C unless otherwise noted)

STATIC PARAMETERS

Parameter

Conditions

IDSS

mA

Gate Threshold Voltage

VDS=VGS ID=-250mA

VDS=-48V, VGS=0V

Body Diode Reverse Recovery Time

Body Diode Reverse Recovery Charge IF=-12A, dI/dt=100A/ms

Drain-Source Breakdown Voltage

On state drain current

ID=-250mA, VGS=0V

VGS=-10V, VDS=-5V

VGS=-10V, ID=-12A

Reverse Transfer Capacitance

A: The value of R qJA is measured with the device mounted on 1in 2 FR-4 board with 2oz. Copper, in a still air environment with T A =25°C. The

Power dissipation PDSM is based on R qJA and the maximum allowed junction temperature of 150°C. The value in any given application depends

on the user's specific board design, and the maximum temperature of 175°C may be used if the PCB allows it.

B. The power dissipation PD is based on TJ(MAX)=175°C, using junction-to-case thermal resistance, and is more useful in setting the upper

dissipation limit for cases where additional heatsinking is used.

C: Repetitive rating, pulse width limited by junction temperature TJ(MAX)=175°C.

D. The R qJA is the sum of the thermal impedence from junction to case R qJC and case to ambient.

E. The static characteristics in Figures 1 to 6 are obtained using <300

ms pulses, duty cycle 0.5% max.

F. These curves are based on the junction-to-case thermal impedence which is measured with the device mounted to a large heatsink, assuming

a maximum junction temperature of TJ(MAX)=175°C.

G. The maximum current rating is limited by bond-wires.

H. These tests are performed with the device mounted on 1 in 2 FR-4 board with 2oz. Copper, in a still air environment with TA=25°C. The SOA

curve provides a single pulse rating.

*This device is guaranteed green after data code 8X11 (Sep 1ST 2008).

Rev.8.0: August 2019

www.aosmd.com

Page 2 of 6