ADS8321 datasheet(7/18 Pages) TI2

7 / 18 page

ADS8321

SBAS123B

www.ti.com

THEORY OF OPERATION

The ADS8321 is a classic Successive Approximation Reg-

ister (SAR) analog-to-digital converter (ADC). The archi-

tecture is based on capacitive redistribution which inherently

includes a sample/hold function. The converter is fabricated

on a 0.6

µ CMOS process. The architecture and process

allow the ADS8321 to acquire and convert an analog signal

at up to 100,000 conversions per second while consuming

less than 5.5mW from +VCC.

The ADS8321 requires an external reference, an external

clock, and a single power source (VCC). The external refer-

ence can be any voltage between 500mV and VCC/2. The

value of the reference voltage directly sets the range of the

analog input. The reference input current depends on the

conversion rate of the ADS8321.

The external clock can vary between 24kHz (1kHz through-

put) and 2.4MHz (100kHz throughput). The duty cycle of

the clock is essentially unimportant as long as the minimum

high and low times are at least 200ns (4.75V or greater). The

minimum clock frequency is set by the leakage on the

capacitors internal to the ADS8321.

The analog input is provided to two input pins: +In and –In.

When a conversion is initiated, the differential input on these

pins is sampled on the internal capacitor array. While a

conversion is in progress, both inputs are disconnected from

any internal function.

The digital result of the conversion is clocked out by the

DCLOCK input and is provided serially, most significant bit

first, on the DOUT pin. The digital data that is provided on the

DOUT pin is for the conversion currently in progress—there

is no pipeline delay. It is possible to continue to clock the

ADS8321 after the conversion is complete and to obtain the

serial data least significant bit first. See the digital timing

section for more information.

ANALOG INPUT

The analog input is bipolar and fully differential. There are

two general methods of driving the analog input of the

ADS8321: single-ended or differential (see Figure 1). When

the input is single-ended, the –In input is held at a fixed

voltage. The +In input swings around the same voltage and

the peak-to-peak amplitude is 2 • VREF. The value of VREF

determines the range over which the common voltage may

vary (see Figure 2).

When the input is differential, the amplitude of the input is

the difference between the +In and –In input, or; +In – (–In).

A voltage or signal is common to both of these inputs. The

peak-to-peak amplitude of each input is VREF about this

common voltage. However, since the inputs are 180

°C out-

of-phase, the peak-to-peak amplitude of the difference volt-

age is 2 • VREF. The value of VREF also determines the range

of the voltage that may be common to both inputs (see

Figure 3).

In each case, care should be taken to ensure that the output

impedance of the sources driving the +In and –In inputs are

matched. If this is not observed, the two inputs could have

ADS8321

ADS821

Single-Ended Input

Common

Voltage

2 • V

REF

peak-to-peak

Differential Input

Common

Voltage

REF

peak-to-peak

REF

peak-to-peak

FIGURE 1. Methods of Driving the ADS8321—Single-Ended

or Differential.

FIGURE 2. Single-Ended Input—Common Voltage Range

vs VREF.

0.0

0.5

1.0

1.5

2.0

2.5

REF (V)

–1

2.8

2.2

–0.3

4.0

CC = 5V

Single-Ended Input

FIGURE 3. Differential Input—Common Voltage Range vs

VREF.

0.0

0.5

1.0

1.5

2.0

2.5

REF (V)

2.75

CC = 5V

1.95

4.0

–0.3

–1

Differential Input

ADS8321 bảng dữ liệu(PDF) 7 Page - Texas Instruments

ADS8321 bảng dữ liệu(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

bảng dữ liệu tải về

Link URL