G6D-F4PU/G3DZ-F4PU/G6D-F4B/G3DZ-F4B

13

• Insert Short Bars so that the protrusion part of a Short Bar comes

to the wire insertion side. If the Short Bar is inserted in the upside

down direction, the Short Bar may not be inserted securely.

Recommended Ferrules and Crimp Tools

Recommended ferrules

Note: 1.

Make sure that the outer diameter of the wire coating is

smaller than the inner diameter of the insulation sleeve of

the recommended ferrule.

2.

Make sure that the ferrule processing dimensions conform

to the following figures.

3.

Wires of AWG24 to AWG22/0.25 mm2 to 0.34 mm2 are not

certified by UL standard.

4.

Do not connect a ferrule for the applicable wires (AWG17 to

AWG16/1.25 mm2 to 1.5 mm2) with an adjacent terminal

insertion hole.

• Do not drop the Socket or subject it to abnormal vibration or shock

during transportation or mounting. Doing so may result in

deterioration of performance, malfunction, or failure.

• Use a power supply with low noise.

G6D-F4PU/G3DZ-F4PU (Model with Push-In

Plus technology)

1. Connecting Wires to the Push-In Plus Terminal

Part Names of the Terminal

Connecting Wires with Ferrules and Solid Wires

Insert the solid wire or ferrule straight into the terminal until the end

strikes the terminal.

• If a wire is difficult to connect because it is too thin, use a flat-blade

screwdriver in the same way as when connecting stranded wire.

Connecting Stranded Wires

Use the following procedure to connect the wires to the terminal.

1.

Hold a flat-blade screwdriver at an angle and insert it into the

release hole.

The angle should be between 10° and 15°. If the flat-blade

screwdriver is inserted correctly, you will feel the spring in the

release hole.

2.

With the flat-blade screwdriver still inserted into the release hole,

insert the wire into the terminal hole until it strikes the terminal.

3.

Remove the flat-blade screwdriver from the release hole.

Checking Connections

• After the insertion, pull gently on the wire to make sure that it will

not come off and the wire is securely fastened to the terminal.

• To prevent short circuits, insert the stripped part of a stranded or

solid wire or the conductor part of a ferrule until it is hidden inside

the terminal insertion hole.

• If you use recommended ferrules, part of the conductor may be

visible after the ferrule is inserted into the terminal, but the product

insulation distance will still be satisfied.

Applicable

wire

Ferrules

Conductor

length

(mm)

Stripping

length

[mm]

(Ferrules

used)

Recommended ferrules

(mm2) (AWG)

Manufactured

by Phoenix

Contact

Manufactured

by

Weidmuller

Manufactured

by Wago

0.25

24

8

10 AI0,25-8

H0.25/12

FE-0.25-8N-YE

10

12 AI0,25-10

---

---

0.34

22

8

10 AI0,34-8

H0.34/12

FE-0.34-8N-TQ

10

12 AI0,34-10

---

---

0.5

20

8

10 AI0,5-8

H0.5/14

FE-0.5-8N-WH

10

12 AI0,5-10

H0.5/16

FE-0.5-10N-WH

0.75

18

8

10 AI0,75-8

H0.75/14

FE-0.75-8N-GY

10

12 AI0,75-10

H0.75/16

FE-0.75-10N-GY

1/1.25 18/17

810 AI1-8

H1.0/14

FE-1.0-8N-RD

10

12 AI1-10

H1.0/16

FE-1.0-10N-RD

1.25/1.5 17/16

8

10 AI1,5-8

H1.5/14

FE-1.5-8N-BK

10

12 AI1,5-10

H1.5/16

FE-1.5-10N-BK

Recommended crimp tool

CRIMPFOX6

CRIMPFOX6T-F

CRIMPFOX10S

PZ6 roto

Variocrimp4

NG

OK

8 to 10 mm

1.9 mm max.

2.6 mm max.

Precautions for Correct Use

Release hole

Terminal (insertion) hole

Short bar insertion hole

Release hole

Terminal (insertion) hole

Ferrules or solid wires

(1)

(3)

(2)

(2)

Flat-blade

screwdriver

Stranded wires

10° to 15°

(1)

(3)