PM50CSD060 datasheet(3/4 Pages) POWEREX

3 / 4 page

PM50CSD060

Intellimod™ Module

Three Phase IGBT Inverter Output

50 Amperes/600 Volts

Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272

Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified

Characteristics

Symbol

Test Conditions

Min.

Typ.

Max.

Units

Control Sector

Over Current Trip Level Inverter Part

Tj = -20°C

——

220

Amperes

(VD = 15V)

Tj = 25°C

109

128

180

Amperes

Tj = 125°C65

——

Amperes

Short Circuit Trip Level Inverter Part

-20

°C ≤ Tj ≤ 125°C, VD = 15V

—

132

—

Amperes

Over Current Delay Time

toff(OC)

VD = 15V

—

µS

Over Temperature Protection (VD = 15V)

Trip Level

111

118

125

°C

(Lower Arm)

OTR

Reset Level

—

100

—

°C

Supply Circuit Under Voltage Protection

Trip Level

11.5

12.0

12.5

Volts

(-20

≤ Tj ≤ 125°C)

UVR

Reset Level

—

12.5

—

Volts

Circuit Current

VD = 15V, VCIN = 15V, VN1-VNC

—

VD = 15V, VCIN = 15V, VXP1-VXPC

—

Input ON Threshold Voltage

VCIN(on)

Applied between

1.2

1.5

1.8

Volts

Input OFF Threshold Voltage

VCIN(off)

UP, VP, WP, UN, VN, WN-VNC

1.7

2.0

2.3

Volts

Fault Output Current*

IFO(H)

VD = 15V, VFO = 15V

——

0.01

IFO(L)

VD = 15V, VFO = 15V

—

Minimum Fault Output Pulse Width*

tFO

VD = 15V

1.0

1.8

—

*Fault output is given only when the internal OC, SC, OT and UV protections schemes of either upper or lower devide operate to protect it.

Thermal Characteristics

Characteristic

Symbol

Condition

Min.

Typ.

Max.

Units

Junction to Case Thermal Resistance

Rth(j-c)Q

Each IGBT

——

1.00

°C/Watt

Rth(j-c)F

Each FWDi

——

2.50

°C/Watt

Rth(j-c´)Q

Each IGBT**

——

0.82†

°C/Watt

Rth(j-c´)F

Each FWDi**

——

1.51†

°C/Watt

Contact Thermal Resistance

Rth(c-f)

Case to Fin Per Module,

——

0.027

°C/Watt

Thermal Grease Applied

** TC measured point is just under chip.

† If you use this value, Rth(f-a) should be measured just under the chips.

Recommended Conditions for Use

Characteristic

Symbol

Condition

Value

Units

Supply Voltage

VCC

Applied across P-N Terminals

0 ~ 400

Volts

Control Supply Voltage***

Applied between VUP1-VUPC,

± 1.5

Volts

VN1-VNC, VVP1-VVPC, VWP1-VWPC

Input ON Voltage

VCIN(on)

Applied between

0 ~ 0.8

Volts

Input OFF Voltage

VCIN(off)

UP, VP, WP, UN, VN, WN-VNC

4.0 ~ VD

Volts

PWM Input Frequency

fPWM

Using Application Circuit

0 ~ 20

kHz

Minimum Dead Time

tDEAD

Input Signal

≥ 2.5

µS

*** With ripple satisfying the following conditions: dv/dt swing

≤ ±5V/µs, Variation ≤ 2V peak to peak.

PM50CSD060 bảng dữ liệu(PDF) 3 Page - Powerex Power Semiconductors

PM50CSD060 bảng dữ liệu(HTML) 3 Page - Powerex Power Semiconductors

Html Pages

1 2 3 4

bảng dữ liệu tải về

Link URL