công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

CY7C1333 bảng dữ liệu(PDF) 3 Page - Cypress Semiconductor

tên linh kiện CY7C1333
Giải thích chi tiết về linh kiện  64Kx32 Flow-Thru SRAM with NoBL??Architecture
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  CYPRESS [Cypress Semiconductor]
Trang chủ  http://www.cypress.com
Logo CYPRESS - Cypress Semiconductor

CY7C1333 bảng dữ liệu(HTML) 3 Page - Cypress Semiconductor

  CY7C1333 Datasheet HTML 1Page - Cypress Semiconductor CY7C1333 Datasheet HTML 2Page - Cypress Semiconductor CY7C1333 Datasheet HTML 3Page - Cypress Semiconductor CY7C1333 Datasheet HTML 4Page - Cypress Semiconductor CY7C1333 Datasheet HTML 5Page - Cypress Semiconductor CY7C1333 Datasheet HTML 6Page - Cypress Semiconductor CY7C1333 Datasheet HTML 7Page - Cypress Semiconductor CY7C1333 Datasheet HTML 8Page - Cypress Semiconductor CY7C1333 Datasheet HTML 9Page - Cypress Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 3 / 12 page
background image
CY7C1333
3
Pin Definitions
Pin Number
Name
I/O
Description
49
−44,
81–82, 99,
100, 32–37
A[15:0]
Input-
Synchronous
Address Inputs used to select one of the 65,536 address locations. Sampled at the
rising edge of the CLK.
96–93
BWS[3:0]
Input-
Synchronous
Byte Write Select Inputs, active LOW. Qualified with WE to conduct writes to the
SRAM. Sampled on the rising edge of CLK. BWS0 controls DQ[7:0], BWS1 controls
DQ[15:8], BWS2 controls DQ[23:16], BWS0 controls DQ[31:24].
88
WE
Input-
Synchronous
Write Enable Input, active LOW. Sampled on the rising edge of CLK if CEN is active
LOW. This signal must be asserted LOW to initiate a write sequence.
85
ADV/LD
Input-
Synchronous
Advance/Load Input used to advance the on-chip address counter or load a new
address. When HIGH (and CEN is asserted LOW) the internal burst counter is
advanced. When LOW, a new address can be loaded into the device for an access.
After being deselected, ADV/LD should be driven LOW in order to load a new
address.
89
CLK
Input-Clock
Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified
with CEN. CLK is only recognized if CEN is active LOW.
98
CE1
Input-
Synchronous
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE2 and CE3 to select/deselect the device.
97
CE2
Input-
Synchronous
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE3 to select/deselect the device.
92
CE3
Input-
Synchronous
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE2 to select/deselect the device.
86
OE
Input-
Asynchronous
Output Enable, active LOW. Combined with the synchronous logic block inside the
device to control the direction of the I/O pins. When LOW, the I/O pins are allowed
to behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act
as input data pins. OE is masked during the data portion of a write sequence,
during the first clock when emerging from a deselected state, when the device has
been deselected.
87
CEN
Input-
Synchronous
Clock Enable Input, active LOW. When asserted LOW the clock signal is recog-
nized by the SRAM. When deasserted HIGH the Clock signal is masked. Since
the deasserting CEN does not deselect the device, CEN can be used to extend
the previous cycle when required.
29–28,25–22,
19–18,13–12,
9–6, 3–2,
79–78,75–72,
69–68,63–62
59–56,53–52
DQ[31:0]
I/O-
Synchronous
Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that
is triggered by the rising edge of CLK. As outputs, they deliver the data contained
in the memory location specified by A[15:0] during the previous clock rise of the
read cycle. The direction of the pins is controlled by OE and the internal control
logic. When OE is asserted LOW, the pins can behave as outputs. When HIGH,
DQ[31:0] are placed in a three-state condition. The outputs are automatically
three-stated during the data portion of a write sequence, during the first clock when
emerging from a deselected state, and when the device is deselected, regardless
of the state of OE.
31
Mode
Input
Strap pin
Mode Input. Selects the burst order of the device. Tied HIGH selects the interleaved
burst order. Pulled LOW selects the linear burst order. MODE should not change
states during operation. When left floating Mode will default HIGH, to an interleaved
burst order.
15, 16, 41, 65,
91
VDD
Power Supply
Power supply inputs to the core of the device. Should be connected to 3.3V power
supply.
17, 40, 67, 90
VSS
Ground
Ground for the core of the device. Should be connected to ground of the system.
4, 11, 20, 27,
54, 61, 70, 77
VDDQ
I/O Power
Supply
Power supply for the I/O circuitry. Should be connected to a 3.3V power supply.
5, 10, 14, 21,
26, 55, 60, 66,
71, 76
VSSQ
I/O Ground
Ground for the I/O circuitry. Should be connected to ground of the system.
64
NC
-
No Connect. Reserved for drive strength control input.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com