| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
FM25F02A bảng dữ liệu(PDF) 10 Page - Shanghai Fudan Microelectronics Group Co., Ltd. |
|
|
|||||||||||||||||||||||||||||
FM25F02A bảng dữ liệu(HTML) 10 Page - Shanghai Fudan Microelectronics Group Co., Ltd. |
|
10 / 43 page ![]() 10. Status Register The Read Status Register instruction can be used to provide status on the availability of the Flash memory array, if the device is write enabled or disabled, the state of write protection, Security Sector lock status. The Write Status Register instruction can be used to configure the device write protection features and Security Sector OTP lock. Write access to the Status Register is controlled by the state of the non-volatile Status Register Protect bit (SRP), the Write Enable instruction, and the WP# pin. Factory default for all Status Register bits are 0. S6 S5 S7 S3 S2 S4 S1 S0 R R SRP/ LB BP1 BP0 BP2 WEL WIP STATUS REGISTER PROTECT / LOCK BIT RESERVED BLOCK PROTECT BITS (non-volatile) WRITE ENABLE LATCH ERASE/WRITE IN PROGRESS Figure 4 Status Register 10.1. WIP Bit WIP is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register. During this time the device will ignore further instructions except for the Read Status Register (see tW, tPP, tSE, tBE, and tCE in “ XX 12.6 X X AC Electrical Characteristics X X ”). When the program, erase or write status register (or security sector) instruction has completed, the WIP bit will be cleared to a 0 state indicating the device is ready for further instructions. 10.2. Write Enable Latch bit (WEL) Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to 1 after executing a Write Enable Instruction. The WEL status bit is cleared to 0 when the device is write disabled. A write disable state occurs upon power-up or after any of the following instructions: Write Disable, Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register. 10.3. Block Protect Bits (BP2, BP1, BP0) The Block Protect Bits (BP2, BP1, BP0) are non-volatile read/write bits in the status register (S4, S3, and S2) that provide Write Protection control and status. Block Protect bits can be set using Datasheet FM25F02A 2M-BIT SERIAL FLASH MEMORY Ver 1.3 10 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |