| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LP38501TS-ADJ bảng dữ liệu(PDF) 9 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
LP38501TS-ADJ bảng dữ liệu(HTML) 9 Page - National Semiconductor (TI) |
|
9 / 16 page ![]() Application Information EXTERNAL CAPACITORS The LP3850X requires that at least 10 µF (±20%) capacitors be used at the input and output pins located within one cm of the IC. Larger capacitors may be used without limit on size for both C IN and COUT. Capacitor tolerances such as temperature variation and voltage loading effects must be considered when selecting capacitors to ensure that they will provide the minimum required amount of capacitance under all operating conditions for the application. In general, ceramic capacitors are best for noise bypassing and transient response because of their ultra low ESR. It must be noted that if ceramics are used, only the types with X5R or X7R dielectric ratings should be used (never Z5U or Y5F). Capacitors which have the Z5U or Y5F characteristics will see a drop in capacitance of as much as 50% if their temperature increases from 25°C to 85°C. In addition, the capacitance drops significantly with applied voltage: a typical Z5U or Y5F capacitor can lose as much as 60% of it’s rated capacitance if only half of the rated voltage is applied to it. For these rea- sons, only X5R and X7R ceramics should be used. INPUT CAPACITOR All linear regulators can be affected by the source impedance of the voltage which is connected to the input. If the source impedance is too high, the reactive component of the source may affect the control loop’s phase margin. To ensure prop- er loop operation, the ESR of the capacitor used for C IN must not exceed 0.5 Ohms. Any good quality ceramic ca- pacitor will meet this requirement, as well as many good quality tantalums. Aluminum electrolytic capacitors may also work, but can possibly have an ESR which increases signifi- cantly at cold temperatures. If the ESR of the input capacitor may exceed 0.5 Ohms, it is recommended that a 2.2 µF ce- ramic capacitor be used in parallel, as this will assure stable loop operation. OUTPUT CAPACITOR Any type of capacitor may be used for C OUT, with no limita- tions on minimum or maximum ESR, as long as the minimum amount of capacitance is present. The amount of capacitance can be increased without limit. Increasing the size of C OUT typically will give improved load transient response. SETTING THE OUTPUT VOLTAGE The output voltage of the LP38501/3-ADJ can be set to any value between 0.6V and 5V using two external resistors shown as R1 and R2 in Figure 1. 30028157 FIGURE 1. The value of R2 should always be less than or equal to 10 k Ω for good loop compensation. R1 can be selected for a giv- en V OUT using the following formula: V OUT = VADJ (1 + R1/R2) + IADJ (R1) Where V ADJ is the adjust pin voltage and IADJ is the bias cur- rent flowing into the adjust pin. STABILITY AND PHASE MARGIN Any regulator which operates using a feedback loop must be compensated in such a way as to ensure adequate phase margin, which is defined as the difference between the phase shift and -180 degrees at the frequency where the loop gain crosses unity (0 dB). For most LDO regulators, the ESR of the output capacitor is required to create a zero to add enough phase lead to ensure stable operation. The LP38501 has a unique internal compensation circuit which maintains phase margin regardless of the ESR of the output capacitor, so any type of capacitor may be used. Figure 2 shows the gain/phase plot of the LP38501-ADJ with an output of 1.2V, 10 µF ceramic output capacitor, delivering 2A of load current. It can be seen that the unity-gain crossover occurs at 300 kHz, and the phase margin is about 40° (which is very stable). 30028153 FIGURE 2. Gain-Bandwidth Plot for 2A Load Figure 3 shows the gain and phase with no external load. In this case, the only load is provided by the gain setting resistors (about 12 k Ω total in this test). It is immediately obvious that the unity-gain frequency is significantly lower (dropping to about 500 Hz), at which point the phase margin is 125°. 9 www.national.com |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |