ALUMINUM ELECTROLYTIC CAPACITORS

1

Voltage

Capacitance

105¡C Marking

105¡C Marking

(f3~ f8 ´ 5.4 )

(f8 ´ 10, f10 ´ 10 )

Plastic platform

0.3 MAX.

L

(L±0.3)

+0.1

Ð0.2

C±0.2

H

H

Positive

Negative

1

Voltage

Capacitance

Trade mark

Lot No.

Plastic platform

0.3 MAX.

L±0.5

Pressure relief vent

1. Voltage mark for 6.3V is 6V . In case of marking for f3 units, ÒVÓ for rated

voltage is omitted.

2. In case of marking for f3 units. Lot No is expressed by a digit (month code).

3 Apply to f6.3 ´ 5.8, f6.3 ´ 7.7

C±0.2

Positive

Negative

Lot No.

2

3

U

1

W

2

T

3

1

4

C

5

1

6

0

7

0

8

M

9

C

10

L

11

1

12

G

13

B

14

Configuration

Package code

Size code

Capacitance tolerance (±20%)

Rated Capacitance (10µF)

Rated voltage (16V)

Series name

Type

fD

3

4~10

code

2

1

fD

3 ~ 8 (5.4L)

6.3 ~ 10 (L 5.8)

code

GB

GS

fD

3 ~ 8 (L 7.7)

8 ~ 10 (L = 10)

code

CL

NL

A

B

C

E

L

H

3 ´ 5.4

1.5

3.3

3.3

0.8

5.4

0.5 ~ 0.8

4 ´ 5.4

1.8

4.3

4.3

1.0

5.4

0.5 ~ 0.8

5 ´ 5.4

2.1

5.3

5.3

1.3

5.4

0.5 ~ 0.8

6.3 ´ 5.4

2.4

6.6

6.6

2.2

5.4

0.5 ~ 0.8

6.3 ´ 5.8

2.4

6.6

6.6

2.2

5.8

0.5 ~ 0.8

6.3 ´ 7.7

2.4

6.6

6.6

2.2

7.7

0.5 ~ 0.8

8 ´ 5.4

3.3

8.3

8.3

2.3

5.4

0.5 ~ 0.8

8 ´ 10

2.9

8.3

8.3

3.1

10

0.8 ~ 1.1

10 ´ 10

3.2

10.3

10.3

4.5

10

0.8 ~ 1.1

fD

(mm)

WT

series

Chip Type, Wide Temperature Range

Designed for surface mounting on high density PC board.

Applicable to automatic mounting machine using carrier tape.

Adapted to the RoHS directive (2002/95/EC).

Chip Type

Specifications

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

tan

δ

Stability at Low Temperature

Endurance

Shelf Life

Marking

Performance Characteristics

Item

– 55 ~ +105°C

4 ~ 50V

0.1 ~ 1500µF

±20% at 120Hz, 20°C

After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.

Black print on the case top.

Measurement frequency : 120Hz, Temperature : 20°C

Measurement frequency : 120Hz

After 1000 hours' application of rated voltage

at 105°C, capacitors meet the characteristic

requirements listed at right.

After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4

clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.

Resistance to soldering

heat

The capacitors shall be kept on the hot plate maintained at 250°C

for 30 seconds. After removing from the hot plate and restored

at room temperature, they meet the characteristic requirements

listed at right.

Rated voltage (V)

tan

δ (MAX.)

4

0.40

6.3

0.30

10

0.24

16

0.20

25

0.16

35

0.14

50

0.14

Z– 25°C / Z+20°C

Z– 40°C / Z+20°C

Rated voltage (V)

Impedance ratio

ZT / Z20 (MAX.)

4

7

15

6.3

4

8

10

3

8

16

2

4

25

2

4

35

2

3

50

2

3

WT

Capacitance

change

Leakage current

tan

δ

Within ±25% of initial value for capacitors of

φ3mm unit, and 16V or less.

Within ±20% of initial value for capacitors of 25V or more.

200% or less of initial specified value

Initial specified value or less

Capacitance change

Leakage current

tan

δ

Within ±10% of initial value

Initial specified value or less

Initial specified value or less

Dimension table in next page.

Smaller

ZT

Low

impeadance

WF

Long Life

UT

WZ

High

Temperature

Reflow

CAT.8100V