 |
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
|
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
WPA1206R002-R005 bảng dữ liệu(PDF) 5 Page - Littelfuse |
|
|
|||||||||||||||||||||||||||||
WPA1206R002-R005 bảng dữ liệu(HTML) 5 Page - Littelfuse |
|
|
5 / 7 page  Current Sense Resistor Datasheet © 2024 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 10/29/24 5 Two-Terminal Surface Mount Resistor WPA/B/C Series Test Procedure Specifications ESD HBM, 100pF, 1.5k ohms Repetition: 5 times Component Classification: 5C (25KV) ±1.0% Appearance: Without distinct damage, and the marking shall be legible. Load Life (Operational Life) Test Temperature: 125°C Applied voltage: rated power (derated Power will be required if temp exceeds the derating point of part) Test Period: 1,000 hours (condition D) ±1.0% Appearance: Without distinct damage, and the marking shall be legible. Biased Humidity Test conditions: 85°C and 85% RH 10% of rated power Test Period 1,000 hours ±1.0% Appearance: Without distinct damage, and the marking shall be legible. Temp. Cycling (Thermal Shock) Repeat 1,000 cycles as follows: -55°C for 30 minutes 125°C for 30 minutes Transition time of 1 minute max ±1.0% Appearance: Without distinct damage, and the marking shall be legible. High Temp. Exposure (Storage) Test Temp 125°C Test Period: 1,000 hours No Electrical Load ±1.0% Appearance: Without distinct damage, and the marking shall be legible. Resistance to soldering heat Condition B (Solder dip, no pre-heat) 260°C ±1.0% Parts must meet initial electrical specs. Resistance to Solvents 3 minute soak 2-3 ounce force 10 strokes/repetition 3 repetitions Appearance: Without distinct damage, and the marking shall be legible. Terminal Strength (SMD) Applied force based on part size ±1.0% Appearance: Without distinct damage, and the marking shall be legible. Flammability UL-94 V-0 or V-1 are acceptable Electrical test not required V-0 burning less than 10 seconds or V-1 burning less than 30 seconds Flame Retardance Mounted parts subjected to voltages from 9.0 to 32 VDC (current clamped up to 500A) No Flame when full automotive battery potential is applied. Vibration Frequency: 10-2,000 Hz Acceleration: 5G Test duration: 20 minutes, 12 cycles ±1.0% Appearance: Without distinct damage, and the marking shall be legible. Mechanical Shock Force: 100G peak Test duration: 6 ms Half-sine waveform Velocity: 12.3ft/sec ±1.0% Appearance: Without distinct damage, and the marking shall be legible. Board Flex 90 mm span between fulcrums 2 mm bend 60 seconds minimum holding time ±1.0% Appearance: Without distinct damage, and the marking shall be legible. Solderability Non-activated flux dip: 5-10 seconds SAC solder dip: 5 seconds at 245°C A new solder shall cover minimum of 95%. Reliability Specifications |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Vietnamese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
