CDCE913 datasheet(6/23 Pages) TI

6 / 23 page

www.ti.com

DEVICE CHARACTERISTICS

CDCE913

CDCEL913

SCAS849A – JUNE 2007 – REVISED AUGUST 2007

over recommended operating free-air temperature range (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP(1)

MAX

UNIT

OVERALL PARAMETER

All outputs off, fCLK = 27 MHz,

All PLLS on

IDD

Supply current (see Figure 3)

fVCO = 135 MHz;

Per PLL

fOUT = 27 MHz

VDDOUT = 3.3 V

1.3

No load, all outputs on,

IDD(OUT)

Supply current (see Figure 4 and Figure 5)

fOUT = 27 MHz

VDDOUT = 1.8 V

0.7

Power-down current. Every circuit powered

IDD(PD)

fIN = 0 MHz,

VDD = 1.9 V

μA

down except SDA/SCL

Supply voltage Vdd threshold for power-up

V(PUC)

0.85

1.45

control circuit

fVCO

VCO frequency range of PLL

230

MHz

VDDOUT = 3.3 V

230

fOUT

LVCMOS output frequency

MHz

VDDOUT = 1.8 V

230

LVCMOS PARAMETER

VIK

LVCMOS input voltage

VDD = 1.7 V; II = –18 mA

–1.2

LVCMOS Input current

VI = 0 V or VDD; VDD = 1.9 V

±5

μA

IIH

LVCMOS Input current for S0/S1/S2

VI = VDD; VDD = 1.9 V

μA

IIL

LVCMOS Input current for S0/S1/S2

VI = 0 V; VDD = 1.9 V

–4

μA

Input capacitance at Xin/Clk

VIClk = 0 V or VDD

Input capacitance at Xout

VIXout = 0 V or VDD

Input capacitance at S0/S1/S2

VIS = 0 V or VDD

CDCE913 - LVCMOS PARAMETER FOR VDDOUT = 3.3 V – MODE

VDDOUT = 3 V, IOH = –0.1 mA

2.9

VOH

LVCMOS high-level output voltage

VDDOUT = 3 V, IOH = –8 mA

2.4

VDDOUT = 3 V, IOH = –12 mA

2.2

VDDOUT = 3 V, IOL = 0.1 mA

0.1

VOL

LVCMOS low-level output voltage

VDDOUT = 3 V, IOL = 8 mA

0.5

VDDOUT = 3 V, IOL = 12 mA

0.8

tPLH, tPHL

Propagation delay

PLL bypass

3.2

tr/tf

Rise and fall time

VDDOUT = 3.3 V (20%–80%)

0.6

tjit(cc)

Cycle-to-cycle jitter(2) (3)

1 PLL switching, Y2-to-Y3

tjit(per)

Peak-to-peak period jitter(3)

1 PLL switching, Y2-to-Y3

100

tsk(o)

Output skew (4) , See Table 2

fOUT = 50 MHz; Y1-to-Y3

odc

Output duty cycle (5)

fVCO = 100 MHz; Pdiv = 1

45%

55%

CDCE913 – LVCMOS PARAMETER for VDDOUT = 2.5 V – Mode

VDDOUT = 2.3 V, IOH = –0.1 mA

2.2

VOH

LVCMOS high-level output voltage

VDDOUT = 2.3 V, IOH = –6 mA

1.7

VDDOUT = 2.3 V, IOH = –10 mA

1.6

VDDOUT = 2.3 V, IOL = 0.1 mA

0.1

VOL

LVCMOS low-level output voltage

VDDOUT = 2.3 V, IOL = 6 mA

0.5

VDDOUT = 2.3 V, IOL = 10 mA

0.7

tPLH, tPHL

Propagation delay

PLL bypass

3.6

tr/tf

Rise and fall time

VDDOUT = 2.5 V (20%–80%)

0.8

tjit(cc)

Cycle-to-cycle jitter(2) (3)

1 PLL switching, Y2-to-Y3

tjit(per)

Peak-to-peak period jitter(3)

1 PLL switching, Y2-to-Y3

100

tsk(o)

Output skew(4) , See Table 2

fOUT = 50 MHz; Y1-to-Y3

odc

Output duty cycle(5)

fVCO = 100 MHz; Pdiv = 1

45%

55%

(1)

All typical values are at respective nominal VDD.

(2)

10000 cycles.

(3)

Jitter depends on configuration. Jitter data is for input frequency = 27 MHz, fVCO = 108 MHz, fOUT = 27 MHz (measured at Y2).

(4)

The tsk(o) specification is only valid for equal loading of each bank of outputs, and the outputs are generated from the same divider.

(5)

odc depends on output rise and fall time (tr/tf); data sampled on rising edge (tr)

Submit Documentation Feedback

Product Folder Link(s): CDCE913 CDCEL913

CDCE913 bảng dữ liệu(PDF) 6 Page - Texas Instruments

CDCE913 bảng dữ liệu(HTML) 6 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

bảng dữ liệu tải về

Link URL