Data Sheet

RH5596S-CSH

SPECIFICATIONS

analog.com

Rev. A | 7 of 12

Table 1. Electrical Characteristics (Continued)

Parameter

Test Conditions

Temperature1

Min

Typ

Max

Unit

EN Input Low Voltage (Off)

Full

0.6

V

EN Pin Input Current

50

500

nA

Turn-On Time10

50 Ω load at OUT

8

μs

Turn-Off Time11

50 Ω load at OUT

45

ns

1 MΩ||11 pF load at

OUT

100

μs

POWER SUPPLY

Supply Voltage

Full

2.7

3.3

3.6

V

Active Supply Current

EN = 3.3 V

25

30

35

mA

Shutdown Supply Current

EN = 0 V

50

500

nA

1 The RH5596S-CSH is guaranteed functional over the case temperature range –40°C to +125°C. All limits at –40°C and +125°C are guaranteed by 100% production

testing.

2 Log linearity error is the input-referred power measurement error relative to the best fit straight line (VOUT vs. pin in dBm) obtained by linear regression at TA = 25°C. The

input power range used for the linear regression is from –32 dBm to +5 dBm for 50 MHz, from –37 dBm to –5 dBm for 100 MHz through 35 GHz, from –34 dBm to –5 dBm

for 38 GHz, from–32 dBm to –5 dBm for 40 GHz, and from –28 dBm to –5 dBm for 43.5 GHz. An offset of 0.5 dB is added to the log intercept for frequencies from 50 MHz

to 38 GHz, and 0.25 dB is added for 40 GHz and 43.5 GHz to center the errors over the full temperature range. See also the LTC5596 data sheet for an explanation of

measurement error metrics.

3 Range for which the log linearity error is within ±1 dB.

4 Slope of the best fit straight line obtained by linear regression.

5 Extrapolated input power level (straight line obtained by linear regression) where the voltage at OUT equals 0 V.

6 Power range for which log linearity error is within ±1 dB, relative to best fit straight line for continuous wave data (see footnote 2).

7 Delay from 50% change in RFIN to 50% change in output voltage.

8 Time required to change voltage at OUT pin from 10% to 90% of final value. Input power stepped from –55 dBm to 0 dBm.

9 Time required to change voltage at OUT pin from 90% to 10% of initial value. Input power stepped from 0 dBm to –55 dBm.

10 Time required to change voltage at OUT pin to 90% of final value. Input power 0 dBm.

11 Time required to change voltage at OUT pin to 10% of initial value. Input power 0 dBm. For higher load impedance, the turn-off time is larger because the OUT interface is

high-impedance in shutdown mode.

BURN-IN DELTA LIMIT SPECIFICATIONS

Electrical characteristics at VCC = 3.3 V and EN = 3.3 V. Continuous wave, 50 Ω source at RFIN, and fRF = 2140 MHz. Delta limits apply at room

temperature (TA = 25°C) for post 240 hour burn-in test. Delta calculation is based on absolute maximum changes.

Table 2. Burn-In Delta Limit Specifications

Parameter1, 2

Test Conditions/Comments

Delta

Unit

ACTIVE SUPPLY CURRENT

±3.5

mA

OUTPUT DC VOLTAGE

fRF = 100 MHz, 2.14 GHz, 8 GHz, 18 GHz, 20 GHz

PIN = 5 dBm

±0.2

V

1 Delta = Max (Absolute (Maximum Post 240 Hour Burn-in Data − Minimum Pre 240 Hour Burn-in Data), Absolute (Minimum Post 240 Hour Burn-in Data − Maximum Pre 240

Hour Burn-in Data)).

2 Devices are not serialized during testing.