6AS5 datasheet(6/23 Pages) HONEYWELL

6 / 23 page

6 sensing.honeywell.com

BZ | BA | BM | BE | 6AS Series

ELECTRICAL DATA AND UL CODES

Table 2. UL Electrical Ratings

Code

Circuitry

Electrical data and UL codes

SPDT

15 A, 125, 250 or 480 Vac;

1⁄8 HP, 125 Vac; 1⁄4 HP, 250 Vac;

1⁄2 A, 125 Vdc; 1⁄4 amp, 250 Vdc.

UL Code L96

SPDT

5 A, 125, 250 or 480 Vac;

1⁄2 A, 125 Vdc; 1⁄4 amp, 250 Vdc.

UL Code L35

SPDT

10 A, 125, 250 or 480 Vac;

UL Code L8

SPDT

15 A, 125, 250 or 480 Vac;

1⁄8 HP, 125 Vac; 1⁄4 HP, 250 Vac.

UL Code L103

SPDT

15 A, 125, 250 or 480 Vac;

1⁄4 HP, 125 Vac, 1⁄2 HP, 250 Vac;

1⁄2 A, 125 Vdc; 1⁄4 amp, 250 Vdc.

UL Code L67

SPDT

22 A, 125, 250 or 480 Vac;

1⁄2 HP, 125 Vac, 1 HP, 250 Vac.

UL Code L161

SPDT

20 A, 125, 250 or 480 Vac;

10 A, 125 Vac ‘‘L’’ (tungsten lamp load);

1 HP, 125 Vac; 2 HP, 250 Vac;

1⁄2 A, 125 Vdc; 1⁄4 A, 250 Vdc. UL Code L23

SPDT

Motor control - 25 A, 125, 250 or 480 Vac;

1 HP, 125 Vac; 2 HP, 250 Vac;

Pilot duty—750 VA, 125, 250, or 277 Vac

SPDT

10 A, 125, 250 or 480 Vac;

1⁄8 HP, 125 Vac; 1⁄4 HP, 250 Vac;

UL Code L95

SPDT

1 A, 125 Vac

UL Code L22

Two-circuit,

double

break

Motor Control

15 A, 120, 240, 480 or 600 Vac;

1⁄2 HP, 120 Vac; 1 HP, 240 Vac;

0.8 amp, 115 Vdc; 0.4 amp, 230 Vdc.

SPST

20 A, 125, 250 or 277 Vac;

3⁄4 HP, 125 Vac; 1⁄2 HP, 250 Vac

UL Code L178B

SPDT

15 A, 125, 250 or 480 Vac;

2 A, 600 Vac; 1⁄8 HP, 125 Vac;

1⁄4 HP, 250 Vac; 1⁄2 amp, 125 Vdc;

1⁄4 amp, 250 Vdc. UL Code L74

GENERAL SWITCH IDENTIFICATION

The first letter in the catalog listing designates:

B = Single pole, double throw

W = Single pole, normally closed

Y = Single pole, normally open

The second letter in the catalog listing designates:

Z = Standard, 15 A version

M = 22 A version

A = Standard, 20 A version

E = 25 A version

MOUNTING DIMENSIONS

Mounting dimensions are included in this datasheet. They are

shown in English and metric equivalents. These dimensions are

for reference only. Engineering drawings may be accessed via the

Honeywell web site:

sensing.honeywell.com.

Mounting holes for Types BZ, BM,BA, BE, and 6AS switches accept

pins or screws of 3,53 mm [0.139 in] diameter.

RECOMMENDED TORQUE

Mounting screws ........................0,39 Nm [3 in-lb]*

Terminal screws.......................... 0,45 Nm [4 in-lb]

Panel mount bushing .... 0,45 Nm to 0,68 Nm [4 in-lb to 6 in-lb]

*Note: Tightening mounting screws above 0,3 Nm [3 in-lb] changes

operating characteristics and increases the possibility of cracking

the case.

UL/CSA

Honeywell basic switches are Component Recognized by

Underwriters’ Laboratories, Inc. and certified by Canadian

Standards Association. The BA, BZ, and BM line is covered

as Special Use Switches to UL Standard1054; the BE line is

covered as an Industrial Product to UL Standard 508. Agency File

References are:

• BA UL File E12252, issued 12-09-88

• BM UL File E12252, issued 12-08-88

• BZ UL File E12252, issued 6-29-89

• BE-1,2,5 UL File E22779, Vol. 4, Sec. 1

• BE-R UL File E22779, Vol. 4, Sec. 2

6AS5 bảng dữ liệu(PDF) 6 Page - Honeywell Solid State Electronics Center

6AS5 bảng dữ liệu(HTML) 6 Page - Honeywell Solid State Electronics Center

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

bảng dữ liệu tải về

Link URL