PIC18F23K20-ESLASHPSQTP datasheet(53/420 Pages) MICROCHIP

53 / 420 page

Advance Information

DS41303B-page 51

PIC18F2XK20/4XK20

4.2

Master Clear (MCLR)

The MCLR pin provides a method for triggering an

external Reset of the device. A Reset is generated by

holding the pin low. These devices have a noise filter in

the MCLR Reset path which detects and ignores small

pulses.

The MCLR pin is not driven low by any internal Resets,

including the WDT.

In PIC18F2XK20/4XK20 devices, the MCLR input can

be disabled with the MCLRE Configuration bit. When

MCLR is disabled, the pin becomes a digital input. See

Section 10.6 “PORTE, TRISE and LATE Registers”

for more information.

4.3

Power-on Reset (POR)

A Power-on

Reset

pulse

generated on-chip

whenever VDD rises above a certain threshold. This

allows the device to start in the initialized state when

VDD is adequate for operation.

To take advantage of the POR circuitry, tie the MCLR

pin through a resistor (1 k

Ω to 10 kΩ) to VDD. This will

eliminate external RC components usually needed to

create a Power-on Reset delay. A minimum rise rate for

VDD is specified (parameter D004). For a slow rise

time, see Figure 4-2.

When the device starts normal operation (i.e., exits the

Reset condition), device operating parameters (volt-

age, frequency, temperature, etc.) must be met to

ensure operation. If these conditions are not met, the

device must be held in Reset until the operating

conditions are met.

POR events are captured by the POR bit of the RCON

POR occurs; it does not change for any other Reset

event. POR is not reset to ‘1’ by any hardware event.

To capture multiple events, the user must manually set

the bit to ‘1’ by software following any POR.

FIGURE 4-2:

EXTERNAL POWER-ON

RESET CIRCUIT (FOR

SLOW VDD POWER-UP)

Note 1:

External Power-on Reset circuit is required

only if the VDD power-up slope is too slow.

The diode D helps discharge the capacitor

quickly when VDD powers down.

R < 40 k

Ω is recommended to make sure that

the voltage drop across R does not violate

the device’s electrical specification.

≥ 1 kΩ will limit any current flowing into

MCLR from external capacitor C, in the event

MCLR/VPP

breakdown,

due

Electrostatic Discharge (ESD) or Electrical

Overstress (EOS).

VDD

MCLR

VDD

PIC® MCU

PIC18F23K20-E/PSQTP bảng dữ liệu(PDF) 53 Page - Microchip Technology

PIC18F23K20-E/PSQTP bảng dữ liệu(HTML) 53 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL