| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AX88796ALF bảng dữ liệu(PDF) 14 Page - ASIX Electronics Corporation |
|
|
|||||||||||||||||||||||||||||
AX88796ALF bảng dữ liệu(HTML) 14 Page - ASIX Electronics Corporation |
|
14 / 68 page ![]() 14 AX88796ALF 3-in-1 Local Bus Fast Ethernet Controller Copyright © 2006-2013 ASIX Electronics Corporation. All rights reserved. 2.2 10/100Mbps Twisted-Pair Interface Pins Group SIGNAL TYPE PIN NO. DESCRIPTION TPIP I 70 Received Data. Positive differential received 125M baud MLT3 or 10M baud Manchester data from magnetic. TPIN I 71 Received Data. Negative differential received 125M baud MLT3 or 10M baud Manchester data from magnetic. TPOP O 88 Transmit Data. Positive differential transmit 125M baud MLT3 or 10M baud Manchester data to magnetic. TPON O 87 Transmit Data. Negative differential transmit 125M baud MLT3 or 10M baud Manchester data to magnetic. REXT10 O 84 No connection REXT100 I/PD 83 Keep this pin floating or pull down REXTBS I 74 External Bias Resistor. Band Gap Reference for the Receive Channel. Connect this signal to a 24.9k-ohm +/- 1 percent resistor to ground. TAB - 2 10/100Mbps Twisted-Pair Interfaces pins group 2.3 Built-in PHY LED Indicator Pins Group SIGNAL TYPE PIN NO. DESCRIPTION I_ACT or I_FULL/COL O 62 Active Status: When I_OP is logic 1. If there is activity, transmit or receive, on the line occurred, the output will be blinking. Full-Duplex/Collision Status. When I_OP is logic 0. If this signal is low, it indicates full-duplex link established, and if it is high, then the link is in half-duplex mode. When in half-duplex and collision occurrence, the output will be blinking. (Current sink capacity is 8mA) I_SPEED O 61 Speed Status: If this signal is low, it indicates 100Mbps, and if it is high, then the speed is 10Mbps. (Current sink capacity is 8mA) This pin will be hold on previous state when loss link. I_LINK or I_LK/ACT O 60 Link Status: When I_OP is logic 1. If this signal is low, it indicates link, and if it is high, then the link is fail. Link Status/Active: When I_OP is logic 0. If this signal is low, it indicates link, and if it is high, then the link is fail. When in link status and line activity occurrence, the output will be blinking. (Current sink capacity is 8mA) TAB - 3 Built-in PHY LED indicator pins group |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |