công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

MAX9394 bảng dữ liệu(PDF) 10 Page - Maxim Integrated Products

tên linh kiện MAX9394
Giải thích chi tiết về linh kiện  2:1 Multiplexers and 1:2 Demultiplexers with Loopback
PDF  14 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  MAXIM [Maxim Integrated Products]
Trang chủ  https://www.maximintegrated.com/en.html
Logo MAXIM - Maxim Integrated Products

MAX9394 bảng dữ liệu(HTML) 10 Page - Maxim Integrated Products

Back Button MAX9394 Datasheet HTML 6Page - Maxim Integrated Products MAX9394 Datasheet HTML 7Page - Maxim Integrated Products MAX9394 Datasheet HTML 8Page - Maxim Integrated Products MAX9394 Datasheet HTML 9Page - Maxim Integrated Products MAX9394 Datasheet HTML 10Page - Maxim Integrated Products MAX9394 Datasheet HTML 11Page - Maxim Integrated Products MAX9394 Datasheet HTML 12Page - Maxim Integrated Products MAX9394 Datasheet HTML 13Page - Maxim Integrated Products MAX9394 Datasheet HTML 14Page - Maxim Integrated Products  
Zoom Inzoom in Zoom Outzoom out
 10 / 14 page
background image
Differential Outputs
The output common-mode voltage is not properly
established if the LVDS output is higher than 0.6V when
the supply voltage is ramping up at power-on. This
condition can occur when an LVDS output drives an
LVDS input on the same chip. To avoid this situation for
the MAX9394/MAX9395, connect a 10k
Ω resistor from
the noninverting output (OUT_) to ground, and connect
a 10k
Ω resistor from the inverting output (OUT_) to
ground. These pulldown resistors keep the output
below 0.6V when the supply is ramping up (Figure 7).
Power-Supply Bypassing
Bypass each VCC to GND with high-frequency surface-
mount ceramic 0.1µF and 0.01µF capacitors in parallel
as close to the device as possible. Install the 0.01µF
capacitor closest to the device.
Differential Traces
Input and output trace characteristics affect the perfor-
mance of the MAX9394/MAX9395. Connect each input
and output to a 50
Ω characteristic impedance trace.
Maintain the distance between differential traces and
eliminate sharp corners to avoid discontinuities in dif-
ferential impedance and maximize common-mode
noise immunity. Minimize the number of vias on the dif-
ferential input and output traces to prevent impedance
discontinuities. Reduce reflections by maintaining the
50
Ω characteristic impedance through connectors and
across cables. Minimize skew by matching the electri-
cal length of the traces.
Output Termination
Terminate LVDS outputs with a 100
Ω resistor between
the differential outputs at the receiver inputs. LVDS out-
puts require 100
Ω termination for proper operation.
Ensure that the output currents do not exceed the cur-
rent limits specified in the Absolute Maximum Ratings.
Observe the total thermal limits of the MAX9394/
MAX9395 under all operating conditions.
Cables and Connectors
Use matched differential impedance for transmission
media. Use cables and connectors with matched differ-
ential impedance to minimize impedance discontinu-
ities. Avoid the use of unbalanced cables.
Balanced cables such as twisted pair offer superior
signal quality and tend to generate less EMI due to
canceling effects.
Board Layout
Use a four-layer printed circuit (PC) board providing
separate signal, power, and ground planes for high-
speed signaling applications. Bypass VCC to GND as
close to the device as possible. Install termination
resistors as close to receiver inputs as possible. Match
the electrical length of the differential traces to minimize
signal skew.
2:1 Multiplexers and 1:2 Demultiplexers with
Loopback
10
______________________________________________________________________________________
LB_SEL_
OUT_ _
GND or open
Normal inputs selected.
VCC
Loopback inputs selected.
Table 2. Loopback Select Truth Table
LOGIC INPUTS
DIFFERENTIAL OUTPUTS
LB_SELA
LB_SELB
BSEL
OUTA_ /
OUTA_
OUTB /
OUTB
0
0
0
INA selected
INB0 selected
0
0
1
INA selected
INB1 selected
0
1
X
INA selected
INA selected
1
0
0
INB0 selected
INB0 selected
1
0
1
INB1 selected
INB1 selected
1
1
0
INB0 selected
INA selected
1
1
1
INB1 selected
INA selected
Table 1. Input Select Truth Table
X = Don’t care.
100
Ω DIFFERENTIAL
TRANSMISSION LINE
100
Ω
TERMINATION
RESISTOR
10k
Ω
GND
10k
Ω
OUT_
OUT_
MAX9394
MAX9395
Figure 7. Pulldown Resistor Configuration for LVDS Outputs



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com