| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
HA17431FP bảng dữ liệu(PDF) 15 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
HA17431FP bảng dữ liệu(HTML) 15 Page - Renesas Technology Corp |
|
15 / 20 page ![]() HA17431 Series REJ03D0678-0300 Rev.3.00 Apr 03, 2007 Page 15 of 19 Design Guide for AC-DC SMPS (Switching Mode Power Supply) 1. Use of Shunt Regulator in Transformer Secondary Side Control This example is applicable to both forward transformers and flyback transformers. A shunt regulator is used on the secondary side as an error amplifier, and feedback to the primary side is provided via a photocoupler. R1 R2 R3 R4 Transformer Photocoupler Light emitting diode Phototransistor Output C1 R5 REF GND A K VK IB IF HA17431 VF SBD PWM IC HA17384 HA17385 Vref V0 (+) (–) Figure 2 Typical Shunt Regulator/Error Amplifier 2. Determination of External Constants for the Shunt Regulator A. DC characteristic determination In figure 2, R1 and R2 are protection resistor for the light emitting diode in the photocoupler, and R2 is a bypass resistor to feed IK minimum, and these are determined as shown below. The photocoupler specification should be obtained separately from the manufacturer. Using the parameters in figure 2, the following formulas are obtained: R1 = V0 – VF – VK IF + IB , R2 = VF IB VK is the HA17431 operating voltage, and is set at around 3 V, taking into account a margin for fluctuation. R2 is the current shunt resistance for the light emitting diode, in which a bias current IB of around 1/5 IF flows. Next, the output voltage can be determined by R3 and R4, and the following formula is obtained: V0 = R3 + R4 R4 × Vref, Vref = 2.5 V Typ The absolute values of R3 and R4 are determined by the HA17431 reference input current Iref and the AC characteristics described in the next section. The Iref value is around 3.8 µA Typ. (V version: 2 µA Typ) B. AC characteristic determination This refers to the determination of the gain frequency characteristic of the shunt regulator as an error amplifier. Taking the configuration in figure 2, the error amplifier characteristic is as shown in figure 3. When R5 = 0 When R5 ≠ 0 G1 f1 fAC f2 G2 fOSC Frequency f (Hz) * fOSC : PWM switching frequency Figure 3 HA17431 Error Amplification Characteristic |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |