MCP1827-0802ESLASHAT datasheet(7/32 Pages) MICROCHIP

7 / 32 page

DS22001C-page 7

MCP1827/MCP1827S

Voltage Regulation

VOUT

VR - 2.5%

±0.5%

VR + 2.5%

Note 2

Dropout Characteristics

Dropout Voltage

VIN-VOUT

—

330

600

Note 5, IOUT = 1.5A,

VIN(MIN) =2.3V

Power Good Characteristics

PWRGD Input Voltage Operat-

ing Range

VPWRGD_VIN

1.0

—

6.0

TA = +25°C

1.2

—

6.0

TA = -40°C to +125°C

For VIN < 2.3V, ISINK = 100 µA

PWRGD Threshold Voltage

(Referenced to VOUT)

VPWRGD_TH

%VOUT Falling Edge

VOUT < 2.5V Fixed, VOUT = Adj.

VOUT >= 2.5V Fixed

PWRGD Threshold Hysteresis

VPWRGD_HYS

1.0

2.0

3.0

%VOUT

PWRGD Output Voltage Low

VPWRGD_L

—0.2

0.4

VIPWRGD SINK = 1.2 mA,

ADJ = 0V

PWRGD Leakage

PWRGD_LK

—1

—

VPWRGD = VIN = 6.0V

PWRGD Time Delay

TPG

—

200

—

µs

Rising Edge

RPULLUP = 10 kΩ

Detect Threshold to PWRGD

Active Time Delay

TVDET-PWRGD

—

200

—

µs

VADJ or VOUT = VPWRGD_TH +

20 mV to VPWRGD_TH - 20 mV

Shutdown Input

Logic High Input

VSHDN-HIGH

%VIN

VIN = 2.3V to 6.0V

Logic Low Input

VSHDN-LOW

%VIN

VIN = 2.3V to 6.0V

SHDN Input Leakage Current

SHDNILK

-0.1

±0.001

+0.1

µA

VIN = 6V, SHDN =VIN,

SHDN = GND

AC Performance

Output Delay From SHDN

TOR

100

µs

SHDN = GND to VIN

VOUT = GND to 95% VR

Output Noise

—2.0

—

µV/

√Hz IOUT = 200 mA, f = 1 kHz, COUT

= 10 µF (X7R Ceramic), VOUT =

2.5V

AC/DC CHARACTERISTICS (CONTINUED)

Electrical Specifications: Unless otherwise noted, VIN = VOUT(MAX) + VDROPOUT(MAX) Note 1, VR=1.8V for Adjustable Output,

IOUT = 1 mA, CIN = COUT = 4.7 µF (X7R Ceramic), TA = +25°C. Boldface type applies for junction temperatures, TJ (Note 7) of

-40°C to +125°C

Parameters

Sym

Min

Typ

Max

Units

Conditions

Note 1:

The minimum VIN must meet two conditions: VIN ≥ 2.3V and VIN ≥ VOUT(MAX) + VDROPOUT(MAX).

VR is the nominal regulator output voltage for the fixed cases. VR = 1.2V, 1.8V, etc. VR is the desired set point output

voltage for the adjustable cases. VR = VADJ * ((R1/R2)+1). Figure 4-1.

TCVOUT = (VOUT-HIGH – VOUT-LOW) *106 / (VR * ΔTemperature). VOUT-HIGH is the highest voltage measured over the

temperature range. VOUT-LOW is the lowest voltage measured over the temperature range.

Load regulation is measured at a constant junction temperature using low duty-cycle pulse testing. Load regulation is

tested over a load range from 1 mA to the maximum specified output current.

Dropout voltage is defined as the input-to-output voltage differential at which the output voltage drops 2% below its

nominal value that was measured with an input voltage of VIN = VOUTMAX + VDROPOUT(MAX).

The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction

temperature and the thermal resistance from junction to air. (i.e., TA, TJ, θJA). Exceeding the maximum allowable power

dissipation will cause the device operating junction temperature to exceed the maximum +150°C rating. Sustained

junction temperatures above 150°C can impact device reliability.

The junction temperature is approximated by soaking the device under test at an ambient temperature equal to the

desired junction temperature. The test time is small enough such that the rise in the junction temperature over the

ambient temperature is not significant.

MCP1827-0802E/AT bảng dữ liệu(PDF) 7 Page - Microchip Technology

MCP1827-0802E/AT bảng dữ liệu(HTML) 7 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

bảng dữ liệu tải về

Link URL