TC1264_06 datasheet(2/18 Pages) MICROCHIP

2 / 18 page

TC1264

DS21375C-page 2

1.0

ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings †

Input Voltage .........................................................6.5V

Output Voltage.................. (VSS – 0.3V) to (VIN + 0.3V)

Power Dissipation................Internally Limited (Note 8)

Maximum Voltage on Any Pin ........VIN +0.3V to -0.3V

Operating Temperature Range...... -40°C < TJ < 125°C

Storage Temperature..........................-65°C to +150°C

† Notice: Stresses above those listed under "Maximum

Ratings" may cause permanent damage to the device. This is

a stress rating only and functional operation of the device at

those or any other conditions above those indicated in the

operation listings of this specification is not implied. Exposure

to maximum rating conditions for extended periods may affect

device reliability.

DC CHARACTERISTICS

Electrical Specifications: Unless otherwise indicated, VIN = VR + 1.5V, (Note 1), IL = 100 µA, CL = 3.3 µF, SHDN > VIH,

TA = +25°C. Boldface type specifications apply for junction temperatures of -40°C to +125°C.

Parameters

Sym

Min

Typ

Max

Units

Conditions

Input Operating Voltage

VIN

2.7

—

6.0

Note 2

Maximum Output Current

IOUTMAX

800

——

Output Voltage

VOUT

VR – 2.5% VR ± 0.5% VR + 2.5%

VVR ≥ 2.5V

VR – 2%

VR ± 0.5% VR + 3%

VR = 1.8V

VR – 7%

—

VR + 3%

IL = 0.1 mA to 800 mA

(Note 3)

VOUT Temperature Coefficient

ΔVOUT/ΔT

—

ppm/°C Note 4

Line Regulation

ΔVOUT/ΔVIN

—0.007

0.35

%(VR + 1V) ≤ VIN ≤ 6V

Load Regulation (Note 5)

ΔVOUT/VOUT

-0.01

0.002

%/mA

IL = 0.1 mA to IOUTMAX

Dropout Voltage (Note 6)

VIN–VOUT

—20

VR ≥ 2.5V, IL = 100 µA

—50

160

VR ≥ 2.5V, IL = 100 mA

—

150

480

VR ≥ 2.5V, IL = 300 mA

—

260

800

VR ≥ 2.5V, IL = 500 mA

—

450

1300

VR ≥ 2.5V, IL = 800 mA

—

1000

1200

VR = 1.8V, IL = 500 mA

—

1200

1400

IL = 800 mA

Supply Current

IDD

—80

130

µA

SHDN = VIH, IL = 0

Power Supply Rejection Ratio

PSRR

—

≤ 1kHz

Output Short Circuit Current

IOUTSC

—

1200

—

VOUT = 0V

Note 1:

VR is the regulator output voltage setting.

2: The minimum VIN has to justify the conditions: VIN ≥ VR + VDROPOUT and VIN ≥ 2.7V for IL = 0.1 mA to IOUTMAX.

This accuracy represents the worst-case over the entire output current and temperature range.

Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested

over a load range from 0.1 mA to the maximum specified output current. Changes in output voltage due to heating

effects are covered by the thermal regulation specification.

Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal

value measured at a 1.5V differential.

Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,

excluding load or line regulation effects. Specifications are for a current pulse equal to ILMAX at VIN = 6V for T = 10 ms.

The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction tem-

perature and the thermal resistance from junction-to-air (i.e., TA, TJ, θJA). Exceeding the maximum allowable power dis-

sipation causes the device to initiate thermal shutdown. Please see Section 5.0 “Thermal Considerations” for more

details..

TCVOUT

VOUTMAX VOUTMIN

–

() 10

–

VOUT

-------------------------------------------------------------------------

TC1264 bảng dữ liệu(PDF) 2 Page - Microchip Technology

TC1264 bảng dữ liệu(HTML) 2 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

bảng dữ liệu tải về

Link URL