công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

MAX2383 bảng dữ liệu(PDF) 2 Page - Maxim Integrated Products

tên linh kiện MAX2383
Giải thích chi tiết về linh kiện  Evaluation Kit
PDF  5 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  MAXIM [Maxim Integrated Products]
Trang chủ  https://www.maximintegrated.com/en.html
Logo MAXIM - Maxim Integrated Products

MAX2383 bảng dữ liệu(HTML) 2 Page - Maxim Integrated Products

  MAX2383_1 Datasheet HTML 1Page - Maxim Integrated Products MAX2383_1 Datasheet HTML 2Page - Maxim Integrated Products MAX2383_1 Datasheet HTML 3Page - Maxim Integrated Products MAX2383_1 Datasheet HTML 4Page - Maxim Integrated Products MAX2383_1 Datasheet HTML 5Page - Maxim Integrated Products  
Zoom Inzoom in Zoom Outzoom out
 2 / 5 page
background image
Quick Start
Test Equipment Required
• A +3V power supply capable of supplying 50mA.
• An adjustable power supply for gain control.
• An RF signal generator for LO covering the frequen-
cy range of 2270MHz to 2580MHz and output power
range of -15dBm to 0.
• Another RF signal generator for IF with WCDMA mod-
ulation, covering the frequency range of 200MHz to
600MHz, and output power range of
-35dBm to -5dBm.
• A spectrum analyzer with ACPR markers and cover-
ing the frequency range 1900MHz to 2000MHz.
Connections and Setup
1) Set the power supply to +2.85V and turn it off.
2) Set the adjustable power supply to +2.0V and turn it off.
3) Connect the ground terminal to GND.
4) Connect the positive +2.85V terminal to VCC,
LO_EN, and SHDN two-pin headers.
5) Connect the positive terminal of the adjustable
power supply to GC.
6) Set the IF generator to 380MHz and set the power
level to -11.5dBm at the board IF input. Set the mod-
ulation to WCDMA mode. The IF balun loss and the
board loss, including the 3dB resistive matching loss
due to the on-board 390
Ω shunt resistor, account for
about 4.5dB, so the IF power delivered to the
device’s differential LO port is approximately
-16dBm. Keep the RF generator output off.
7) Set the LO generator to 2330MHz and set the
power level to -8dBm. The board loss and the LO
balun loss account for about 2dB, so the LO power
delivered to the device’s differential LO port is
approximately -10dBm. Keep the RF generator out-
put off.
8) Using an SMA cable, connect the output of the IF
generator to the LFIN on the MAX2383 EV kit.
9) Using an SMA cable, connect the output of the LO
generator to the LOIN on the MAX2383 EV kit.
10) Using an SMA cable, connect the DROUT to the
input of the spectrum analyzer.
11) Set the spectrum analyzer to view the output (ACPR
marker, center frequency, etc.).
12) Turn on all power supplies and enable both signal
generators.
13) Observe the RF output frequency as displayed on
the spectrum analyzer. Measure the RF output
power.
Layout Issues
A good PC board is an essential part of an RF circuit
design. The EV kit PC board can serve as a guide for
laying out a board using the MAX2383. Keep the traces
carrying RF signals as short as possible to minimize
radiation and insertion loss. Use impedance control on
all RF signal traces. The VCC node on the PC board
should have decoupling capacitors to the closest
ground. Refer to the Layout section of the MAX2383
data sheet for more information.
MAX2383 Evaluation Kit
2
_______________________________________________________________________________________
Component List (continued)
DESIGNATION
QTY
DESCRIPTION
L7
1
3.3nH inductor (0402)
Toko LL1005-FH-3N3S
R1, R2
2
10k
Ω ±1% resistors (0402)
R3
0
Not installed
R4, R5
2
24
Ω ±1% resistors (0402)
R6
1
390
Ω ±1% resistor (0402)
R7, R8
2
2.4
Ω ±1% resistors (0402)
T1
1
Balun transformer (B4F type)
Toko 617DB-1018
T2
1
Balun transformer
Murata LDB15C201A2400
TL1
1
50
Ω coaxial cable (0.047in
diameter)
LOIN, LFIN,
DROUT
3
SMA connectors (PC edge-mount)
EF Johnson 142-0701-801 DIGI-
KEY J502-ND
DRIN, RFOUT
0
Not installed
JU1, JU2
2
3-pin headers
Digi-Key S1012-36-ND or
Equivalent
None
2
Shunts for JU1–JU12
VCC, GND, GC,
LO_EN, SHDN
5
Test points
Mouser 151-203 or Equivalent
U1
1
MAX2383EBC (12 UCSP)
None
1
MAX2383 PC board
None
1
MAX2383 data sheet
None
1
MAX2383 EV kit data sheet



Html Pages

1 2 3 4 5


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com