CERAMIC LEADED

PACKAGING INFORMATION

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300

40

Ceramic Radial Tape and Reel Dimensions in Millimeters & (Inches)

Figure 3: Standard Reel

Figure 1

(82.6)

.655"

±0.010"

(16.6

±0.25)

12"

(30.48 cm)

.059" to .315"

Greater Than

Over All

Height

of Taped

Components

*

Hub

1/8"

(3.18)

Ceramic Radial

Lead Tape and Reel Packaging

KEMET offers standard reeling of Molded and Conformally

Coated Radial Leaded Ceramic Capacitors for automatic

insertion per EIA specification RS-468. Parts are taped to a

tagboard carrier strip, and wound on a reel as shown in

Figure 1. Kraft paper interleaving is inserted between the

layers of capacitors on the reel. Ammopack is also available,

with the same lead tape configuration and package quantities.

KEMET

®

KEMET

®

Kraft Paper

Interleaving

Carrier Tape

Carrier Strip

Adhesive Tape

* Lead spacings are 2.54mm

(.10") center-to-center.

** Lead spacings are 5.08mm

(.20") center-to-center.

C317**

C322**

C323**

C333**

H

T

C315*

C320*

CK05**

CKR05**

C052**

C056**

C066**

CK06**

CKR06**

C062**

C330**

C340**

P

1MM Max.

(.039")

Tape

Carrier

∆H

P1

F

Figure 2: Lead Tape Configuration (See Table Below)

W

Sprocket Hole Diameter

Sprocket Hole Pitch

Component Pitch

Lead Spacing (1)

Sprocket Hole Center

to Lead Center (1)

Sprocket Hole Center

to Component Center

Height to Seating Plane

(straight leads) (2)

Component Height

Above Tape Center

Dimension

Symbol

Nominal

mm (inch)

Tolerance

mm (inch)

Dimension

Symbol

Nominal

mm (inch)

Tolerance

mm (inch)

Height to Seating

Plane (formed leads) (2)

Component Alignment

Lead Protrusion

Composite Tape

Thickness

Overall Tape and

Lead Thickness

Carrier Tape Width

Hold-Down Tape

Width

Hold-Down Tape

Location

Do

P0

P

F

P1

P2

H

H1

± 0.2 (.008)

± 0.3 (.012)

± 0.3 (.012)

+0.6 -0.2

(+.024 -.008)

± 0.7 (.028)

± 1.3 (.051)

7301

7303

±0.5 (.020) Minimum

Maximum

7301

7303

16.0 (.630) 18.0 (.709)

4.0 (.157)

1.0 (.039)

0.7 (.051)

1.5 (.059)

18.0 (.709)

5.0 (.197)

3.0 (.118)

∆h

L1

t

T

W

W0

W2

7301

7303

±0.5 (.020) Minimum

±0.2 (.008)

Maximum

±0.2 (.008)

Maximum

+1.0 - 0.5

(+.039 -.020)

Minimum

Maximum

(1) Measured at the egress from the carrier tape, on the component side.

(2) Determined by a 4 digit suffix placed at the end of the part number, as follows:

7301 =

7303 =

4.0 (.157)

12.7 (.500)

12.7 (.500)

5.08

2.54

(.20)

(.10)

3.81

5.08

(.150)

(.200)

6.35 (.250)

7301

7303

16.0 (.630) 18.0 (.709)

32.2 (1.27)

Recommended for parts with formed leads.

Recommended for parts with straight leads.

Example: C322C104K5R5CA7301

Example: C320C104K5R5CA7303

(Note: Non-standard lead lengths

available in bulk only.)

C6xx#

C6xx#

# See page 15 for exact lead

configuration for Series.