| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
34701 bảng dữ liệu(PDF) 13 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
34701 bảng dữ liệu(HTML) 13 Page - Freescale Semiconductor, Inc |
|
13 / 38 page ![]() Analog Integrated Circuit Device Data Freescale Semiconductor 13 34701 ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS BOOST REGULATOR Boost Regulator MOSFET Maximum ON Time (21) tON –24– µs Boost Regulator Control Loop Propagation Delay (21) tBST_PD –50– ns Boost Switching Node VBD Rise Time (21) IBST = 20 mA tB_RISE –5.0 ns Boost Switching Node VBD Fall Time (21) IBST = 20 mA tB_FALL –3.0 – ns LINEAR REGULATOR (LDO) Fault Condition Time-Out tFAULT 7.0 10 15 ms Retry Timer Cycle tRet 70 100 150 ms RESET MONITOR (RST) Monitoring LFB Pin Delay tD_RST_LFB 12–28 µs Monitoring INV Pin Delay tD_RST_INV 12–28 µs SCA, SCL PIN, I2C BUS (STANDARD) SCL Clock Frequency (21) fSCL – – 100 kHz Bus Free Time Between a STOP and a START Condition (21) tBUF 4.7 – – µs Hold Time (Repeated) START Condition (After this period, the first clock pulse is generated.) (21) tHD-STA 4.0 – – µs Low Period of the SCL Clock (21) tLOW 4.7 – – µs High Period of the SCL Clock (21) tHIGH 4.0 – – µs SDA Fall Time from VIH_MAX to VIL_MIN, Bus Capacitance 10 pF to 400 pF, 3.0 mA Sink Current (21), (23) tF – – 250 ns Setup Time for a Repeated START Condition (21) tSU-STA 4.7 – – µs Data Hold Time for I2C Bus Devices (21), (22) tHD-DAT 0.0 – – µs Data Setup Time (21) tSU-DAT 250 – – ns Setup Time for STOP Condition (21) tSU-STO 4.0 – – µs Capacitive Load for Each Bus Line (21) CB – – 400 pF Notes 21. Design information only. This parameter is not production tested. 22. The device provides an internal hold time of at least 300 ns for the SDA signal (refer to the V IH_MIN of the SCL signal) to bridge the undefined region of the falling edge of SCL. 23. VIH is High Level Voltage on I2C bus lines and VIL is Low Level Voltage on I2C bus lines Table 4. DYNAMIC ELECTRICAL CHARACTERISTICS (continued) Characteristics noted under conditions -40°C ≤ TA ≤ 85°C unless otherwise noted. Input voltages VIN1 = VIN2 = 3.3 V using the typical application circuit (see Figures 33) unless otherwise noted. Characteristic Symbol Min Typ Max Unit |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |