SPT datasheet(2/2 Pages) SENSATA

2 / 2 page

Rev.12/27/2023

Page 2

Datasheets provided by Sensata Technologies, Inc., its subsidiaries and/or affiliates (“Sensata”) are solely intended to assist third parties

(“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands

and agrees that Buyer remains responsible for using its independent analysis, valuation, and judgment in designing Buyer’s systems

and products. Sensata datasheets have been created using standard laboratory conditions and engineering practices. Sensata has not

conducted any testing other than that specifically described in the published documentation for a particular datasheet. Sensata may

make corrections, enhancements, improvements, and other changes to its datasheets or components without notice.

Buyers are authorized to use Sensata datasheets with the Sensata component(s) identified in each particular datasheet. HOWEVER,

NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY

RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA

DATASHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATASHEETS

OR USE OF THE DATASHEETS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS

ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET

ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD

TO SENSATA DATASHEETS OR USE THEREOF.

All products are sold subject to Sensata’s terms and conditions of sale supplied at www.sensata.com. SENSATA ASSUMES NO

LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT

IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY, AND SAFETY-RELATED REQUIREMENTS CONCERNING

ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED

INFORMATION OR SUPPORT THAT MAY BE PROVIDED BY SENSATA.

Mailing Address: Sensata Technologies, Inc., 529 Pleasant Street, Attleboro, MA 02703, USA

Americas

Newall Electronics Inc.

1803 OBrien Rd

Columbus, OH 43228

Tel: +1 614 771 0213

sales@newall.com

newall.com

Rest of World:

Newall Measurement Systems,

Ltd.

Business Park, Unit 1 Wharf Way

Glen Parva, Leicester LE2 9UT

United Kingdom

Tel: +44 (0) 116 264 2730

sales@newall.co.uk

newall.co.uk

sensata.com/newall

DIMENSIONS

INSTALLATION

The module is to be situated between the encoder and the control system and connected as per the above pin-out. Care must be taken to ensure the

location of the module is such that it is not exposed to environmental conditions beyond its IP rating. Ensure that the connection locking is secure.

Newall Measurement Systems, Ltd: Technology Gateway . Cornwall Road . South Wigston . Leicester . LE18 4XH . England

Newall Electronics, Inc: 1778 Dividend Drive . OH 43228 . USA . Tel: +1 (614) 771 0213 . Fax: +1 (614) 771 0219 . Website: www.newall.com

NOTE: Newall Measurement Systems Ltd. reserves the right to change the specification without notice.

023-81050/2 UK

SPT ENCODER INTERFACE MODULES

DATASHEET

Model

SPT (Part No. 600-83580)

5-28Vin, 5V TTL out

(Line driver 26C31)

Power requirements

Voltage

5V to 28V ± 5%

Ouput power

1.5W max (<150mA at 5V)

Output signals

Differential quadrature signals

A, B, A, B

Phase angle A to B

90º

Frequency range

0-2MHz, equivalent to 2ms-1 with 1μm resolution

Reference mark

Differential Reference RM & RM

As per Encoder

Signal

Periodic or Single Point

Enclosure

Material

Aluminium extrusion

Sealing

IP54

Temperature

Operation

0 to 55ºC

Storage

-20 to 85ºC

Connection Details

Dimensions

ANSI/ESD S8.1-2001

16mm / 0.63in

103mm / 4.06in

33mm / 1.30in

Newall TT or TS Encoder

Control

Installation

The module is to be situated between the encoder and the control system and connected as per the above pin-out. Care must be taken

to ensure the location of the module is such that it is not exposed to environmental conditions beyond its IP rating. Ensure that the con-

nection locking is secure.

Introduction

This power management interface module enables a 5V SHG-TT/TS or MHG-TT linear encoder to operate from a 5-28V supply. Output

levels remain at RS422 5V quadrature levels.

9D Connector

Pin No

Module (Female)

RS422 (Encoder)

Module (Male)

RS422 (Control)

N/C

5V supply out

5-28V supply in

/RM

Shell

Gnd