ST92F124 datasheet(194/429 Pages) STMICROELECTRONICS

194 / 429 page

194/429

MULTIFUNCTION TIMER (MFT)

MULTIFUNCTION TIMER (Cont’d)

10.4.3.1 TxINA = I/O - TxINB = I/O

Input pins A and B are not used by the Timer. The

counter clock is internally generated and the up/

down selection may be made only by software via

the UDC (Software Up/Down) bit in the TCR regis-

ter.

10.4.3.2 TxINA = I/O - TxINB = Trigger

The signal applied to input pin B acts as a trigger

signal on REG1R register. The prescaler clock is

internally generated and the up/down selection

may be made only by software via the UDC (Soft-

ware Up/Down) bit in the TCR register.

10.4.3.3 TxINA = Gate - TxINB = I/O

The signal applied to input pin A acts as a gate sig-

nal for the internal clock (i.e. the counter runs only

when the gate signal is at a low level). The counter

clock is internally generated and the up/down con-

trol may be made only by software via the UDC

(Software Up/Down) bit in the TCR register.

10.4.3.4 TxINA = Gate - TxINB = Trigger

Both input pins A and B are connected to the timer,

with the resulting effect of combining the actions

relating to the previously described configurations.

10.4.3.5 TxINA = I/O - TxINB = Ext. Clock

The signal applied to input pin B is used as the ex-

ternal clock for the prescaler. The up/down selec-

tion may be made only by software via the UDC

(Software Up/Down) bit in the TCR register.

10.4.3.6 TxINA = Trigger - TxINB = I/O

The signal applied to input pin A acts as a trigger

for REG0R, initiating the action for which the reg-

ister was programmed (i.e. a reload or capture).

The prescaler clock is internally generated and the

up/down selection may be made only by software

via the UDC (Software Up/Down) bit in the TCR

(*) The timer is in One shot mode and REGOR in

Reload mode

10.4.3.7 TxINA = Gate - TxINB = Ext. Clock

The signal applied to input pin B, gated by the sig-

nal applied to input pin A, acts as external clock for

the prescaler. The up/down control may be made

only by software action through the UDC bit in the

TCR register.

10.4.3.8 TxINA = Trigger - TxINB = Trigger

The signal applied to input pin A (or B) acts as trig-

ger signal for REG0R (or REG1R), initiating the

action for which the register has been pro-

grammed. The counter clock is internally generat-

ed and the up/down selection may be made only

by software via the UDC (Software Up/Down) bit in

the TCR register.

ST92F124 bảng dữ liệu(PDF) 194 Page - STMicroelectronics

ST92F124 bảng dữ liệu(HTML) 194 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL