LM358AD datasheet(5/12 Pages) PHILIPS

5 / 12 page

Philips Semiconductors

Product data

NE/SA/SE532/

LM258/358/A/2904

Low power dual operational amplifiers

2002 Jul 12

DC ELECTRICAL CHARACTERISTICS (continued)

Tamb = 25 °C; V+ = +5 V; unless otherwise specified.

SYMBOL

PARAMETER

TEST CONDITIONS

LM358A

UNIT

SYMBOL

PARAMETER

TEST CONDITIONS

Min

Typ

Max

UNIT

VOS

Offset voltage1

RS = 0 Ω

±2

±3

VOS

Offset voltage1

RS = 0 Ω; over temp.

±5

VOS

Drift

RS = 0 Ω; over temp.

µV/°C

IOS

Offset current

IIN(+) – IIN(–)

±30

IOS

Offset current

Over temp.

±75

IOS

Drift

Over temp.

300

pA/

°C

Input current2

IIN(+) or IIN(–)

100

IBIAS

Input current2

IIN(+) or IIN(–); Over temp.

200

Drift

Over temp.

pA/

°C

Common mode voltage range3

V+ = 30 V

V+–1.5

VCM

Common-mode voltage range3

V+ = 30 V; Over temp.

V+–2.0

CMRR

Common-mode rejection ratio

V+ = 30 V

Output voltage swing

RL ≥ 2 kΩ; V+ = 30 V; over temp.

VOH

Output voltage swing

RL ≥ 10 kΩ; V+ = 30 V; over temp.

VOL

Output voltage swing

RL ≥ 10 kΩ; over temp.

ICC

Supply current

RL = ∞, V+ = 30 V

0.5

1.0

ICC

Supply current

RL = ∞ on all amplifiers; V+ = 30 V; over temp.

0.6

1.2

A O

Large signal voltage gain

RL ≥ 2 kΩ; VOUT ±10 V

100

V/mV

AVOL

Large-signal voltage gain

V+ = 15 V (for large VO swing); over temp.

V/mV

PSRR

Supply voltage rejection ratio

RS = 0 Ω

100

Amplifier-to-amplifier coupling4

f=1kHz to 20kHz (input referred)

–120

VIN+ = +1 VDC; VIN– = 0 VDC; V+ = 15 VDC

Output current (Source)

VIN+ = +1 VDC; VIN– = 0 VDC; V+ = 15 VDC;

over temp.

IOUT

VIN– = +1 VDC,;VIN+ = 0 VDC; V+ = 15 VDC

Output current (Sink)

VIN– = +1 VDC; VIN+ = 0 VDC;V+ = 15 VDC;

over temp.

VIN+ = 0 V; VIN– = +1 VDC; VO = 200 mV

µA

ISC

Short circuit current5

Differential input voltage6

V+

GBW

Unity gain bandwidth

Tamb = 25 °C

MHz

Slew rate

Tamb = 25 °C

0.3

µs

VNOISE

Input noise voltage

Tamb = 25 °C; f = 1 kHz

nV/

√Hz

NOTES:

1. VO ≈ 1.4 V, RS = 0 Ω with V+ from 5 V to 30 V; and over the full input common-mode range (0 V to V+ –1.5 V).

2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of

the output so no loading change exists on the input lines.

3. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of

the common-mode voltage range is V+ –1.5 V, but either or both inputs can go to +32 V without damage.

4. Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This

typically can be detected as this type of capacitance coupling increases at higher frequencies.

5. Short-circuits from the output to V+ can cause excessive heating and eventual destruction. The maximum output current is approximately

40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15 VDC, continuous short-circuits can exceed the

power dissipation ratings and cause eventual destruction.

6. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of

the common-mode voltage range is V+ –1.5 V, but either or both inputs can go to +32 VDC without damage.

LM358AD bảng dữ liệu(PDF) 5 Page - NXP Semiconductors

LM358AD bảng dữ liệu(HTML) 5 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

bảng dữ liệu tải về

Link URL