công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

CAT93C66 bảng dữ liệu(PDF) 5 Page - Catalyst Semiconductor

tên linh kiện CAT93C66
Giải thích chi tiết về linh kiện  4-Kb Microwire Serial CMOS EEPROM
PDF  17 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  CATALYST [Catalyst Semiconductor]
Trang chủ  http://www.catalyst-semiconductor.com
Logo CATALYST - Catalyst Semiconductor

CAT93C66 bảng dữ liệu(HTML) 5 Page - Catalyst Semiconductor

  CAT93C66 Datasheet HTML 1Page - Catalyst Semiconductor CAT93C66 Datasheet HTML 2Page - Catalyst Semiconductor CAT93C66 Datasheet HTML 3Page - Catalyst Semiconductor CAT93C66 Datasheet HTML 4Page - Catalyst Semiconductor CAT93C66 Datasheet HTML 5Page - Catalyst Semiconductor CAT93C66 Datasheet HTML 6Page - Catalyst Semiconductor CAT93C66 Datasheet HTML 7Page - Catalyst Semiconductor CAT93C66 Datasheet HTML 8Page - Catalyst Semiconductor CAT93C66 Datasheet HTML 9Page - Catalyst Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 5 / 17 page
background image
CAT93C66
© 2007 Catalyst Semiconductor, Inc.
5
Doc. No. 1089 Rev. P
Characteristics subject to change without notice
POWER-UP TIMING
(1) (2)
Symbol
Parameter
Max
Units
tPUR
Power-up to Read Operation
1
ms
tPUW
Power-up to Write Operation
1
ms
Notes
:
(1) These parameters are tested initially and after a design or process change that affects the parameter according to appropriate
AEC-Q100 and JEDEC test methods.
(2) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated.
A.C. TEST CONDITIONS
Input Rise and Fall Times
≤ 50 ns
Input Pulse Voltages
0.4V to 2.4V
4.5V ≤ VCC ≤ 5.5V
Timing Reference Voltages
0.8V, 2.0V
4.5V ≤ VCC ≤ 5.5V
Input Pulse Voltages
0.2VCC to 0.7VCC
1.8V ≤ VCC ≤ 4.5V
Timing Reference Voltages
0.5VCC
1.8V ≤ VCC ≤ 4.5V
Output Load
Current Source IOLmax/IOHmax; CL=100pF
DEVICE OPERATION
The CAT93C66 is a 4096-bit nonvolatile memory
intended for use with industry standard micropro–
cessors. The CAT93C66 can be organized as either
registers of 16 bits or 8 bits. When organized as X16,
seven 11-bit instructions control the reading, writing and
erase operations of the device. When organized as X8,
seven 12-bit instructions control the reading, writing and
erase operations of the device. The CAT93C66 operates
on a single power supply and will generate on chip, the
high voltage required during any write operation.
Instructions, addresses, and write data are clocked
into the DI pin on the rising edge of the clock (SK).
The DO pin is normally in a high impedance state
except when reading data from the device, or when
checking the ready/busy status after a write operation.
The serial communication protocol follows the timing
shown in Figure 1.
The ready/busy status can be determined after the start
of internal write cycle by selecting the device (CS high)
and polling the DO pin; DO low indicates that the write
operation is not completed, while DO high indicates that
the device is ready for the next instruction. If necessary,
the DO pin may be placed back into a high impedance
state during chip select by shifting a dummy “1” into the
DI pin. The DO pin will enter the high impedance state
on the rising edge of the clock (SK). Placing the DO pin
into the high impedance state is recommended in
applications where the DI pin and the DO pin are to be
tied together to form a common DI/O pin.
The format for all instructions sent to the device is a
logical “1” start bit, a 2-bit (or 4-bit) opcode, 8-bit
address (an additional bit when organized X8) and for
write operations a 16-bit data field (8-bit for X8
organizations). The instruction format is shown in
Instruction Set table.
INSTRUCTION SET
Address
Data
Instruction
Start
Bit
Opcode
x8
x16
x8
x16
Comments
READ
1
10
A8-A0
A7-A0
Read Address AN – A0
ERASE
1
11
A8-A0
A7-A0
Clear Address AN – A0
WRITE
1
01
A8-A0
A7-A0
D7-D0
D15-D0
Write Address AN – A0
EWEN
1
00
11XXXXXXX
11XXXXXX
Write Enable
EWDS
1
00
00XXXXXXX
00XXXXXX
Write Disable
ERAL
1
00
10XXXXXXX
10XXXXXX
Clear All Addresses
WRAL
1
00
01XXXXXXX
01XXXXXX
D7-D0
D15-D0
Write All Addresses



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com