COPPERCATALOG datasheet(38/56 Pages) AAO

38 / 56 page

Contact Amphenol Aerospace for more information at 800-678-0141 • www.amphenol-aerospace.com

249

Amphenol

Aerospace

Dualok

III

SJT

38999

PCB

Accessories

Aquacon

Herm/Seal

Fiber

Optics

Contacts

Connectors

Cables

HigH

Speed

Typical Contact Installation Instructions

for Coax Contacts

The following is an example of a contact instruction sheet that would be shipped within the package of contacts for a Crimp, Size 12

Coax Contact for use in Subminiature, D38999 connectors The sheet provides detailed instructions for assembling the component

parts and for crimping the contact to coaxial cable, along with the recommended cable and tooling to be used Installation instructions

are included within all contacts for D38999 connectors For installation instructions for other connector series, there are separate

documents (not included in packaging of parts) as follows: L- 633 for Miniature solder types, L-613 for Miniature SE types, L-660 for

Miniature CE types, and L-650 for MS/Standard and Heavy Duty types For any other instructions needed, consult Amphenol Most

installation instructions can be found on-line at www amphenol-aerospace com (from home page, go to Service Instructions and enter

contact part number or instruction sheet number)

21-033651-011 (PIN)

21-033650-011 (SOCKET)

Contact, Pin and Socket, Coaxial,

Type LJT-R & TV-R, (MIL-DTL-38999 Series I & III) Crimp,

Size 12

Installation Instructions

See table on reverse side for coaxial cable recommended

and crimp tool information

A 1 Slide outer crimp ferrule over cable outer jacket as

shown

2 Strip cable outer braid as illustrated Ends must be cut

cleanly and at right angles to the axial plane of the

cable The cable must not be deformed while making

cuts

3 Flare outer braid, then strip cable dielectric as shown

B 1 Assemble inner contact assembly over cable center

conductor and cable dielectric until inside bore of

bushing butts against cable dielectric

2 Cable center conductor must be visible through the

inspection hole in the inner contact wire well

3 Crimp inner contact wire well using crimp tool listed in

table

C 1 Carefully slide outer contact assembly over inner

contact assembly and under cable outer braid until

inner contact butts against insulator shoulder as

illustrated (Inner contact assembly will snap into the

locked position when fully assembled inside the outer

contact assembly )

2 Bring outer crimp ferrule forward over cable outer

braid as illustrated (Continue to push the inner

contact assembly fully forward while bringing the

outer crimp ferrule into position )

3 Crimp outer crimp ferrule using crimp tool listed in

table ( 156 Max over ferrule after crimping) Trim

excess braid ahead of crimp ferrule, if necessary

CONTACT INSERTION INTO CONNECTOR

Using insertion tool (part number M81969/8-09 or

M81969/14-04), insert contact assembly into rear connector

grommet hole Contact must be aligned with hole and not

inserted at an angle Push forward until contact is felt to snap

into position within insert Remove tool

CONTACT REMOVAL FROM CONNECTOR

Position removal tool (part number M81969/8-10 or

M81969/14-04) around cable and slide tool down wire until

tool tips enter rear grommet and come to a positive stop

Hold tool tip firmly against positive stop on contact, grip wire

and simultaneously remove tool, contact and cable

21-033651-011 (PIN)

21-033650-011 (SOCKET)

L-2092-C October 2001

FSCM77820

.135

.195

CABLE

DIELECTRIC

CABLE

OUTER BRAID

.165

CABLE

CENTER

CONDUCTOR

CABLE

DIELECTRIC

.165

REF.

OUTER CRIMP FERRULE

CABLE OUTER BRAID

CABLE

OUTER JACKET

A & A

OUTER FERRULE

CABLE

OUTER BRAID

.010 / .030

OUTER CONTACT ASSEMBLY

(PIN SHOWN FOR REFERENCE)

INNER CONTACT

MUST BUTT INSULATOR

CABLE CENTER CONDUCTOR

INNER CONTACT ASSEMBLY

(SOCKET SHOWN FOR REFERENCE)

CABLE DIELECTRIC

MUST BUTT

BUSHING

INSPECTION HOLE

.330 REF.

Amphenol ®

Part Number

Description

Coaxial Cable

Accommodated

Tools

Inner Contact

Outer Contact

Crimp Tool

Setting

Positioner

(Daniels)

Tool

Positioner

21-033651-011

Matched Impedance*

Size 12 Coax

RG316

(M17/113-RG316)

MH992 (Daniels)

K1360

M22520/5-01

M22520/5-03 (A)

M22520/5-35 (B)

RG179

(M17/094-RG179)

MH992 (Daniels)

K1360

21-033650-011

Matched Impedance*

Size 12 Coax

Socket

RG316

(M17/113-RG316)

MH992 (Daniels)

K1360

RG179

(M17/094-RG179)

MH992 (Daniels)

K1360

* Matched Impedance applies when contacts are terminated to RG316 cable only

COPPERCATALOG bảng dữ liệu(PDF) 38 Page - Amphenol Aerospace Operations

COPPERCATALOG bảng dữ liệu(HTML) 38 Page - Amphenol Aerospace Operations

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

bảng dữ liệu tải về

Link URL