công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

T4FC2012F-121 bảng dữ liệu(PDF) 3 Page - Transko Electronics, Inc.

tên linh kiện T4FC2012F-121
Giải thích chi tiết về linh kiện  Common Mode Choke SMD (2.0 X 1.2 X 1.2 mm)
PDF  5 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  TRANSKO [Transko Electronics, Inc.]
Trang chủ  https://www.transko.com/
Logo TRANSKO - Transko Electronics, Inc.

T4FC2012F-121 bảng dữ liệu(HTML) 3 Page - Transko Electronics, Inc.

  T4FC2012F-121 Datasheet HTML 1Page - Transko Electronics, Inc. T4FC2012F-121 Datasheet HTML 2Page - Transko Electronics, Inc. T4FC2012F-121 Datasheet HTML 3Page - Transko Electronics, Inc. T4FC2012F-121 Datasheet HTML 4Page - Transko Electronics, Inc. T4FC2012F-121 Datasheet HTML 5Page - Transko Electronics, Inc.  
Zoom Inzoom in Zoom Outzoom out
 3 / 5 page
background image
T4FC2012F SERIES
3981 E. Miraloma Ave. Anaheim, CA 92806 USA
Tel: 714-528-8000
www.transko.com
sales@transko.com
Rev 1: 05
-
09
-
2018
Operating temperature : -40 to +125°C
Storage temp and humidity : -40~125°C ,60% RH max
ITEM
SPECIFICATIONS
TEST CONDITIONS
Solderability
The metalized area must have 90%
minimum solder coverage.
Dip pads in flux and dip in solder pot (99 Sn or 96.5
Sn/3.5 Ag solder) at 232°C ±5°C.
Resistance to soldering heat
There must be no case deformation
or change in dimensions.
Inductance must not change more
than the stated tolerance.
Inductors shall be reflowed onto a PC board using
96.5 Sn/3.5 Ag or 99 Sn solder paste.
Solder process shall be at a maximum temperature
of 260°C.
For 99 Sn solder paste: >183°C for 120 sec.
For 96.5 Sn/3.5 Ag solder paste: >217°C for 90 sec
Vibration
There must be no case deformation
or change in dimensions.
Inductance must not change more
than the stated tolerance.
Solder specimen inductor on the test printed circuit
board. Apply vibrations in each of the x,y and z
directions for 2 house for a total of 6 hours.
Frequency : 10~50 Hz ; Amplitude : 1.5mm
High temperature resistance
There must be no case deformation
or change in dimensions.
Inductance must not change more
than the stated tolerance.
Inductors shall be subjected to temperature 125±2°C
for 500±12 hours. Measure the test items after
leaving the inductors at room temperature and
humidity for 2 hours.
Static Humidity
Inductors must not have a shorted
or open winding.
Inductors shall be subjected to temperature 85±2°C
and 90 to 95%RH. for ten 24-hours. Measure the
test items after leaving the inductors at room
temperature and humidity for 2 hours.
Component adhesion
(push test)
Inductors shall be subjected to
1.8Kg
Inductors shall be reflow soldered (232°C ±5°C for
10 seconds) to a tinned copper substrate. A force
gauge shall be applied to the side of the component.
The device must withstand the stated force without a
failure of the termination.
Low temperature storage
There must be no case deformation
or change in dimensions.
Inductance must not change more
than the stated tolerance.
Inductors shall be subjected to temperature -40±2°C
for 48±12 hours. Measure the test items after leaving
the inductors at room temperature and humidity for
1 to 2hours.
Resistance to solvent
There must be no case deformation
or change in dimensions, or
obliteration of marking
Inductors must withstand 6 minutes of alcohol or
water.
Thermal shock
There must be no case deformation
or change in dimensions.
Inductance must not change more
than the stated tolerance.
Inductors shall be subjected to 10 cycles to the
following temperature cycle:
Measure the test items after leaving the inductors at
room temperature and humidity for 2 hours.
RELIABILITY TEST



Html Pages

1 2 3 4 5


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com